1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

MR-SA152-1

★ ★ ★ ★ ★ Rated 0/5 Based on ratings.

Rate your purchase of the MR-SA152-1

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

The Mitsubishi MR-SA152-1 servo drive or servo amplifier is an industrial device that can control servo motors. It is a member of the Mitsubishi MELSERVO-SA servo amplifier series. The MR-SA152-1 servo amplifier controls a servo motor’s speed, position, and torque during operation. The MR-SA152-1 servo amplifier can receive signals that are too weak for the servo motor to use, and it can amplify those signals until they are strong enough to be used by the servo motor. This servo amplifier is AC-powered and it uses 3-phase AC voltage. The MR-SA152-1 servo amplifier operates at 200 Volts AC to 220 Volts AC with a frequency rating of 50 Hertz or 60 Hertz. The current rating of the MR-SA152-1 servo amplifier is 8 Amps. The MR-SA152-1 servo amplifier weighs about 20 pounds. It was designed to be mounted vertically on a wall. The MR-SA152-1 servo amplifier can be mounted on a wall with bolts or screws. This device generates heat when it operates, and it needs to be installed in an area where it will have enough free space around it for heat dissipation. The MR-SA152-1 servo amplifier needs at least 40 millimeters of free space around it to dissipate heat. The ambient operating temperature range for the MR-SA152-1 servo amplifier is between 0 degrees Celsius and 55 degrees Celsius. This servo amplifier should not be subjected to freezing conditions or exposed to direct sunlight or to corrosive gases. The MR-SA152-1 servo amplifier can tolerate about 90% maximum relative humidity if there is no condensation in its environment.

Technical Specifications for MR-SA152-1

Manufacturer:Mitsubishi
Series:MELSERVO-SA
Part number:MR-SA152-1
Product type:Servo Amplifier
Voltage type:3-phase AC voltage
Voltage range:200-220V AC
Frequency:50/60 Hertz
Weight:About 20 pounds
Operating temperature:0 to 55 degrees Celsius
Relative humidity:90% (non-condensing)

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.