1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

MR-JE-70A

★ ★ ★ ★ ★ Rated 0/5 Based on ratings.

Rate your purchase of the MR-JE-70A

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

New

$690

1 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?

The MR-JE-70A is an industrial servo amplifier from Mitsubishi Electric. It is compatible with the Mitsubishi HG-KN73 and HG-SN52 series servo motors. When used with HG-KN73 series motors, the MR-JE-70A servo amplifier’s power supply capacity is 1.3 kVA, the heat generated at the rated output is 50 Watts, and the heat generated with the servo off is 15 Watts. When used with HG-SN52 series motors, the MR-JE-70A servo amplifier’s power supply capacity is 1. kVA, the heat generated at the rated output is 40 Watts, and the heat generated with the servo off is 15 Watts. The MR-JE-70A servo amplifier’s input voltage range is 200 to 240 Volts AC. The servo amplifier works with either single-phase or 3-phase input voltage. The rated input current is 3.8 Amps. The permissible voltage fluctuation range is 170 to 264 Volts AC. The inrush current rating of the servo amplifier at 240 Volts AC input is 36 Amps, which attenuates to 7 Amps in 20 milliseconds. The power rating of the built-in regenerative resistor is 20 Watts. The output ratings of the MR-JE-70A servo amplifier are 170 Volts AC of voltage and 5.8 Amps of current. The interface power supply specifications are 24 Volts DC of voltage and 0.3 Amps of current. The control method supported by the servo amplifier is sine-wave PWM control or current control. A dynamic brake is installed on the unit. The MR-JE-70A supports 2 ports. One port is a USB port that supports communication with a personal computer. The other port is an RS-422/RS-485 port for connecting to a controller. The MR-JE-70A servo amplifier supports 3 control modes: the speed control mode, the torque control mode, and the position control mode.

Technical Specifications for MR-JE-70A

Power supply input200-240V AC
Permissible voltage fluctuation170-264V AC
Inrush current36 Amps
Output voltage170V AC
Communication portsUSB, RS-422/RS-485
Output current5.8 Amps
Input current3.8 Amps
ControlSine-wave PWM control, current control
Interface power supply voltage24 Volts DC
Dynamic brakeYes

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.