1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

MR-J2S-500B

★ ★ ★ ★ ★ Rated 0/5 Based on ratings.

Rate your purchase of the MR-J2S-500B

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

New

$2950

2 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?

The MR-J2S-500B is 5 kilowatts rated servo amplifier with a Mitsubishi-oriented MELSERVO MR-J2 series; its first power supply is the control circuit, which operates at a voltage of 200 to 230 volts alternating current (AC) with a frequency of 50/60 hertz and runs on 1-phase; the voltage can even be varied to 170 to 253 volts AC. The second power supply is for the primary circuit, which is equivalent to the control circuit. The frequency may be allowed to vary between +5% and -5%. The control circuit power consumption of the servo amplifier is 50 watts. The MR-J2S-500B MR-J2 servo amplifier features four inputs and six outputs. The CN1A port is the first of these. This CN1A port interfaces with the motion control and positioning control modules. These control modules are from either the Mitsubishi A or Q series. The following port connects to another servo amplifier or a terminal connector (MR-A-TM). The SSCNET system is supported by both the CN1A and CN1B ports. The servo motor can then be connected to the MR-J2S-500B servo amplifier's CN2 port. Finally, the CN3 port can communicate with a computer via the MR Configurator program to make an RS-232C connection. The MR-J2S-500B servo amplifier's display panel includes a battery compartment that may house the MR-BAT battery as well as the axis setting area. There are numerous servo motors to which the MR-J2S-500B MELSERVO MR-J2 servo amplifier can link. The following servo motors are associated with this servo amplifier. Its ambient air temperature for operation varies from 0 to 55 degrees Celsius.

Technical Specifications for MR-J2S-500B

ManufacturerMitsubishi Electric
SeriesMELSERVO J2S
Product TypeAC servo drive
Supply voltage200V-230V AC
Voltage Class200V class
Power Supply1-phase input or 3-phase input
Rated active power5000W / 5kW
Digital inputs1 digital input (Sink/Source)
Digital output1 digital relay
DimensionsH (250mm) x W (130mm) x D (200mm)
Ambient air temperature for operation0 to 55 °C
Protection functionsYes

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.