1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

HA-FF33

★ ★ ★ ★ ★ Rated 0/5 Based on ratings.

Rate your purchase of the HA-FF33

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

New

$990

2 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?

The HA-FF33 motor is an industrial servo motor from Mitsubishi Electric. It is a low inertia and small capacity servo motor. The rated output of the motor is 300 Watts. The rated torque output is 0.95 Nm. The rated and maximum shaft speeds of the HA-FF33 motor are 3000 RPM and 4000 RPM, respectively. The instantaneous permissible motor speed is 4600 RPM. The maximum torque output is 2.9 Nm. The power rate at the continuous rated torque is 18.1 kilowatts per second. The inertia rating is 0.5 kg-cm2. The recommended rate for the motor shaft’s conversion load inertia is 10 times the motor inertia rating or less. The rated continuous motor current is 1.9 Amps and the maximum current is 5.7 Amps. The regenerative brake duty for the built-in regenerative resistor is 1500 times per minute. The HA-FF33 motor’s armature insulation class is class B. The motor structure is enclosed and it has an IP44 ingress protection rating. The mass of the motor is approximately 2.6 kilograms. The HA-FF33 motor does not include an electromagnetic brake. The motor and any associated equipment must only be installed on incombustible material, and a load bearing location that is in compliance with the motor’s specifications should be used for motor installation. The temperature of air in the operating environment must not exceed 40 degrees Celsius. The HA-FF33 servo motor can be connected to a servo amplifier, and it can be installed in any orientation. When installed horizontally, the HA-FF33 motor should be installed with the connector section oriented downwards.

Technical Specifications for HA-FF33

Rated speed3000 RPM
Max speed4000 RPM
Power output300 Watts
Protection ratingIP44
Weight2.6 kilograms
Length148 millimeters
Rated torque0.95 Nm
Max torque2.9 Nm
Rated current1.9 Amps
Max current5.7 Amps

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.