1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

AI61

★ ★ ★ ★ ★ Rated 0/5 Based on ratings.

Rate your purchase of the AI61

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

New

$750

2 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?

The AI61 is a Mitsubishi interruption input unit (DC input) for MELSEC-A series programmable controllers. The unit has 16 interruption input points and 32 I/O occupying points. At 12 Volts DC input voltage, the input current is 6 milliamps and at 24 Volts DC input voltage, the input current is 14 milliamps. The operating voltage range for the AI61 unit is 10.2 to 26.4 Volts DC. All 16 input points on the AI61 unit can be ON simultaneously. The ON voltage rating is 9 Volts or higher, and the ON current rating is 4.5 milliamps or higher. The OFF voltage rating is 6 Volts or lower. The input resistance of each input is approximately 2.4 kiloohms. The ON to OFF state response time is less than or equal to 0.2 milliseconds. The OFF to ON state response time is less than or equal to 0.2 milliseconds. The typical internal current consumption at 5 Volts DC, with all the supported points in the ON state, is 14 milliamps. An LED indicator on the AI61 interruption unit indicates when the unit is on. The weight of the AI61 interrupting unit is 0.4 kilograms. Mitsubishi recommends wire with a 0.75 to 2 mm2 cross sectional area. The applicable tightening torque is 7 kg-cm. The AI61 unit must be protected from impacts and shock. The printed circuit board for the AI61 unit must not be removed from its case. The AI61 unit’s ambient temperature range for operation is 0 and 55 degrees Celsius. The dielectric withstand voltage rating of the AI61 unit is 500 Volts AC for 60 seconds.

Technical Specifications for AI61

Inputs16
Weight0.4 kg
Operating temperature0 to 55 degrees Celsius
Operating humidity10 to 90%
CoolingSelf cooling
InsulationPhotocoupler
Operating voltage10.2 to 26.4 Volts DC
Internal current consumption14 milliamps
Power indicator LEDSupported
Dielectric withstand500 Volts AC

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.