1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC200MDL940-PDF

SKU 2176053  UPC 012404391264

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description


The IC200MDL940 is a Form A Relay VersaMax Output Module from General Electric with a total of 16 output points. The output points for this device are divided into two groups of eight, and each point is also isolated individually. Group to group and channel to channel isolation are also possible. The IC200MDL940 has fixed coil relay types with moving armatures, and the contact types are silver. This module is compatible with both the IC200CHS101 and IC200CHS102 series of VersaMax interposing disconnect bases.

 

The IC200MDL940 will consume up to 490 milliamps of current from a five-volt output backplane from which this device receives its primary power. For all load switching, however, another power supply will be needed. The output voltage for the IC200MDL940 has two settings: alternating current and direct current. With alternating current, the output voltage can range from 0 to 265 volts at 47 to 63 hertz, but the nominal voltage is 120 volts and 240 volts. When using direct current, the output voltage is 0 to 125 volts, but the nominal voltage is 5 volts, 24 volts, or 125 volts.

 

The load current for each point is a minimum of 10 milliamps; however, this will change depending on voltage conditions. With 5 to 265 volts of alternating current, the load per point will be 2 amperes maximum. When using 5 to 30 volts direct current, the load per point will also be at most 2 amperes. With 31 to 125 volts direct current, the load per point will be 0.2 amperes. Note: These load currents are all resistive. Thermal derating, fuses, and snubbers are not applicable to the IC200MDL940. 

In Stock! Output relay 2.0 amps per point isolated form A, 16 points IC200M IC200MD IC200MDL
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, User-Manual, Wiring, 

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.