GE / IP FANUC Series 90/30 In Stock
IC697PWR713
SKU 2175311 UPC 0799705792807
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC697PWR713 IC697PWR713-CAIC697PWR713-LTIC697PWR713-RR
Common misspellings:
- 1C697PWR713
- IC697PWR7l3
- IC697PWR713
Product Description
The IC697PWR713 is a 100 Watt Power Supply Module for the 90-70 Series produced by GE Fanuc. Features include operation from 120 VAC, 240 VAC, or 125 VDC, and there are three output voltages (100 watts total) as follows: +5 VDC output up to 20 amps; +12 VDC output up to 2 amps; -12 VDC output up to 1 amp. Other highlights include slide-in rack mount construction, electronic short circuit overcurrent protection, two rack operation from a single power supply, power factor correction for AC operation, and a jumper for overvoltage protection devices.
The IC697PWR713 is rack-mounted and plugs into a 48-pin backplane-mounted connector in the leftmost slot of any standard IC697 rack or VME Integrator’s rack. It provides +5 volt, +12 volt and -12 volt power, and logic level sequencing signals to the backplane. The module can be used in a single rack application and can also provide power to a second rack if the total load is within the supply rating. A prewired cable permits interconnection to the second rack. The power supply output will ride through at least one input line cycle with a total loss of input power at full load. Protection is supplied for overcurrent and overvoltage fault conditions.
This module includes an electronic overvoltage protection circuit that will turn the output off if the 5 V bus exceeds 6.2 +0.5 V. To reset, the power supply must first be turned OFF. External overvoltage on the output that prompted the overvoltage protection will not cause the power supply fuse to open. If an internal fault in the power supply caused the overvoltage condition, then the fuse may open. This fuse should be replaced with a 3AG 3 amp, 250 V fuse.
The IC697PWR713 power supply provides electronic overcurrent protection for each of the three outputs. If the max current rating is exceeded, the voltage will collapse to a low value. It will continue in that state until the load is removed or reduced. A current overload (including a short circuit condition) will not cause the fuse to open. This power supply does not comply with FCC requirements in non-industrial applications for conducted EMI on AC power lines.
Technical Specifications
| Nominal Rated Voltage | 120/240 VAC or 125 VDC |
| Input Voltage Range: | 90 to 264 VAC or 100 to 150 VDC |
| Input Power: | 135 watts at full load |
| Output Power: | 100 watts |
| Location on Baseplates: | Leftmost Slot |
| DC Output: | + 5VDC, +12 VDC and -12 VDC |
Technical Information
Specifications
Nominal Rated Voltage: |
120/240 VAC, or 125 VDC |
Input Voltage Range: |
|
AC Input |
90 to 264 VAC, 47 to 63 Hz |
DC Input |
100 to 150 VDC |
Input Power:Input Half Cycle Peak Inrush Power Factor |
135 watts (typical), 160 watts (maximum)3 amps (typical)> .93 |
Output Power: 2 |
100 watts maximum (total for all 3 outputs) |
Output Voltage: |
+5 VDC: 4.90 to 5.25 volts (5.07 volts nominal) |
|
|
+12 VDC: 11.64 to 12.6 volts 3 |
|
|
-12 VDC: -12.6 to -11.64 volts 3 |
Protective Limits - Overvoltage Limit: Overcurrent Limit: |
+5 VDC Output: 5.7 to 6.7 volts+5 VDC output: 21A (typical)+12 VDC output: 3.5A (typical)-12 VDC output: 1.6A (typical) |
Holdup Time: |
21 milliseconds minimum (from loss of AC input) |
Environmental -Operating Temperature: |
0°C to 60°C (32° to 140°F) operating2–40°C to +85°C (-40° to +185°F) storage |
NOTES:
1 Refer to latest revision of data sheet GFK-0867 for product standards and general specifications.
2 Derate for continuous low input voltage (see Figure 1)
3 In GFK–1448C, Output Voltage values shown in this table were changed to align with VME standards (previous values were 11.75 to 12.6 and –12.6 to –11.75).
Troubleshooting
Troubleshooting IC697PWR713
Troubleshooting information is available on IC697PWR713's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC697PWR713
PDF Supply can repair your IC697PWR713 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC697PWR713? Answer: The IC697PWR713 is an 120/240 VAC or 125 VDC, 100W Power Supply module from the GE Fanuc 90-70 Series.
- Question: Into where does this unit plug? Answer: IC697PWR713 is a rack-mounted unit that plugs directly into a 48-pin backplane-mounted connector in the leftmost slot in the rack.
- Question: Once there, what does it provide? Answer: IC697PWR713 provides +5 volt, +12 volt, and -12 volt power (as well as logic level sequencing signals to the backplane).
- Question: What are some of the features that IC697PWR713 provides? Answer:
- Operation from 120/240 VAC or 125 VDC
- 3 output voltages (100 watts total): +5 VDC output up to 20 amps, +12 VDC output up to 2 amps, and -12 VDC output up to 1 amp
- Slide-in rack mount construction
- Electronic short circuit overcurrent protection
- 2 rack operation from a single power supply
- Power factor corrected on AC inputs
- Jumper for overvoltage protection devices
- Question: Can this unit only provide power to a single rack application? Answer: No. This unit can, yes, provide power to a single rack application, but it can also be used to provide power to a second rack (as long as the total load is within the supply rating).
- Question: Is protection provided for overcurrent and overvoltage fault conditions? Answer: Yes, it is.
- Question: What should happen when you plug in this unit and hit the power button? Answer:
- You should get a green LED light on, as well as the LED on the CPU should be lit up (letting you know it's providing power to the CPU).
- Question: What should be my next step if my IC697PWR713 is not working properly? Answer: Your IC697PWR713 may be in need of repair.
For more information on the IC697PWR713 120/240 VAC or 125 VDC, 100W Power Supply Module of the GE Fanuc 90-70 Series, please see the Datasheet User-Manual.
Common related search terms: DatasheetEmerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
