GE / IP FANUC Series 90/30 In Stock
IC697MDL752
SKU 2170205 UPC 0635850377189
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC697MDL752 IC697MDL752AIC697MDL752BIC697MDL752CIC697MDL752-CAIC697MDL752DIC697MDL752EIC697MDL752FIC697MDL752GIC697MDL752HIC697MDL752IIC697MDL752JIC697MDL752KIC697MDL752LIC697MDL752-LTIC697MDL752MIC697MDL752NIC697MDL752OIC697MDL752PIC697MDL752-RR
Common misspellings:
- 1C697MDL752
- IC697MD1752
- IC697MDL752
Product Description
The GE Fanuc 90-70 Series module IC697MDL752 is a 32-point module that delivers 12 Volts and 0.5 Amperes of current. This module provides a high level of inrush current, which makes the IC697MDL752 ideal for a wide array of loads, such as motor starters and solenoids. To find the ON-OFF status of each point of the circuit, locate the LED indicators on the top of the module. In order to ensure correct alignment with similar modules in the field, the module is properly keyed. This IC697MDL752 module is configured using MS-DOS or programming software that rides on either Windows NT or Windows 95. This is usually over the TCP/IP protocol over Ethernet cable or SNP port. The programming configuration is downloaded and installed on the programming device. This is done using a device such as a personal computer, IBM XT, PS/2 or AT.
The IC697MDL752 12 Volt output module is compatible with many devices such as motor starters, solenoids, and indicators. It is divided into 4 groups, each having 8 modules. Due to the module’s heat dissipation, the largest current for each of the 4 groups has a 2-ampere limit.
Each output module can deliver a surge current greater than its life-time current rating. This capability is dependent on the device’s current rating and the duration of time the device is powered ON.
The output module comes with a mechanical key that provides a fool proof mechanism. This ensures the module is properly positioned and prevents modules from being unintentionally substituted into a slot for a different module type. Each module comes with a key for this purpose.
During installation or removal of the terminal boards, it’s highly recommended that the power is shut off. Once the power has been shut down, the hinged door can be opened to access the jack screw, which firmly secures the terminal board in place.
The terminal board is designed to accommodate wire sizes from AWG 0.36 mm2 to AWG 2.1mm2. It’s crucial to note that a maximum insulation diameter of .135 inch should not be exceeded when dealing with a 2.1mm2 wire for wiring all points. For proper connection, two wires can be terminated on any terminal provided they are of the same size. The terminal board is crafted to accommodate a maximum of 40 2.1mm2 wires. If they are used, they should be placed at least 8 inches from the end of the termination. This creates sufficient space for the hinged door to close with ease.
After all connections are made to the cable modules, it’s recommended that the cable ties wrap tightly around the wire bundles. When handling larger wire bundles, additional cable ties are recommended.
After completing filed wiring, ensure the terminal board is fastened to the rack. This is achieved by inserting the board strap into the small slots at the bottom card guide grill on the rack. The strap also identifies the terminal board with its accurate mating slot location.
Technical Specifications
| Rated Voltage: | 12 volts DC |
| Number of Outputs: | 32 Outputs (4 groups of 8) |
| Output Current: | 0.5 Amps per point, 2 Amps per group |
| Current Required: | 0.25 Amps |
| Output Voltage Range: | 10 to 15 volts |
| DC Power: | Yes |
Technical Information
Specifications
|
Rated Voltage: OutputsperModule: |
12 volts DC 32 (four groups of 8 outputs each) |
|
Isolation: |
1500 volts - any output to backplane 500 volts between input groups |
|
Output VoltageRange: OutputCurrent: |
10 to 15 volts 0.5 amps maximum per point 2 amps maximum per group |
|
OutputCharacteristics |
|
|
Inrush Current: |
10 amps maximum for 20 ms |
|
Output VoltageDrop: |
1 volt (2 ohms) maximum |
|
ResponseTime-On: |
1 ms typical |
|
ResponseTime-Off: |
1 ms typical |
|
OutputLeakage: |
1mAmaximum |
|
Current Required from 5 V Bus: |
.25 amp |
|
VME |
System designed to support the VME standard C.1 |
Troubleshooting
Troubleshooting IC697MDL752
Troubleshooting information is available on IC697MDL752's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC697MDL752
PDF Supply can repair your IC697MDL752 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC697MDL752? Answer: The IC697MDL752 is a 12 Volt DC, 0.5 Amp, 32-Point Output module from the GE Fanuc 90-70 Series. This module provides 32 points divided into 4 isolated groups of 8 points each.
- Question: What are some of the features that IC697MDL752 provides? Answer:
- 32 points- 4 isolated groups of 8 points each
- 0.5 amp capacity per point
- high inrush capacity (20x rated current)
- Question: The LED indicators (located at the top of the module) do what? Answer: They let you know the on/off status of each point on the logic (PLC) side of the circuit.
- Question: What is special about the I/O references? Answer: They are configurable without the use of jumpers or DIP switches on the module.
- Question: Configuration of IC697MDL752 is done through what? Answer: Configuration of IC697MDL752 is completed using the configuration function of MS-DOS, through Windows programming software on Windows 95, through Windows NT over Ethernet TCP/IP, or through the SNP port.
- Question: What should I do in the event my IC697MDL752 is not working properly? Answer: Your IC697MDL752 may be in need of repair.
For more information on the IC697MDL752 12 Volt DC, 0.5 Amp, 32-Point Output Module of the GE Fanuc 90-70 Series, please see the Datasheet User-Manual.
Common related search terms: DatasheetEmerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
