1-919-535-3180
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-919-535-3180

Mon-Fri 8AM-5PM EST

[email protected]

IC697MDL651J

★★★★★Rated 4.9/5 Based on 6 ratings.

Rate your purchase of the IC697MDL651

SKU 2175303  UPC 0606837998635

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description

The GE IC697MDL651 is a 32-point discrete input module part of the Series 90-70 Programmable Controllers.  It features 32 TTL compatible input points with each input having a pullup resistor. Thus, user power is not required. The input filter selectable is 1ms or 10ms and one input is configurable as interrupt. There are LED indicators present on the top of the module, which provide information about the ON/OFF status of each point of the circuit’s logic (or PLC) side. The rated voltage of IC697MDL651 is 5 volts DC. There are 32 inputs per module with 98.4 (30m) maximum cable length. Isolation is 1500 volts. Input voltage range is between -3 and +7 volts DC. Input characteristics of the module include impedance of 5.9K ohms, ±5%; on-state voltage of -3 to 0.5 volts; off-state voltage of 2 to 7 volts; typical on-state current of 1.7mA at rated voltage and maximum off-state current of 1.1mA. The current required from 5V bus is .53 amp. In addition, the system is designed to support the VME standard C.1.

The IC697MDL651 module is mechanically keyed in order to ensure a similar type in the field can correctly replace it if needed. I/O references can be configured by the user without the need to use DIP switches or jumpers on the module.The above-mentioned mechanical key the module comes with prevents unintended substitution of the wrong module type in the same slot. The key is designed to fit an area on the board below the connector that has a unique shape.  It is important to note that in a IC697 PLC rack, the leftmost position is reserved for a power supply only. In addition, one spot located next to the power supply needs to contain a CPU or a Bus Receiver Module. The input module’s design allows it to have negative logic characteristics. This means it sinks current running from input device to the user common. IC697MDL651 is compatible with different input devices such as limit switches, pushbuttons, selector switches, BCD outputs, counters as well as other TTL compatible outputs.

To configure the device, use the configuration function of Windows or MS-DOS software running on Windows NT or Windows 95 through the SNP port or over Ethernet TCP/IP.  IC697MDL651 is configurable to have 1 ms or 10 ms filter delay time. Configuration is not a per point basis but rather on a module basis, which means that all points have the same filter time. Whenever the IC697MDL651 is used with IC697 CPU, input point A1 can be configured so to cause a CPU interruption either on the falling or the rising edge of signal transition. Input filter time selection does not affect interrupt response. In terms of field wiring, a single connection is required between the module common and user common. This is due to the fact the 32 points share a common. However, for wiring convenience, two connections are provided.

Technical Specifications

Rated Voltage: 5 volts DC
Number of Inputs: 32 Inputs (one group)
Input Current: 1.7 mA at rated voltage
Current Required: 0.53 Amps
Input Voltage Range:  -3 to +7 volts DC
DC Power: Yes

 

5 Volts dc (TTL) Input (32) IC697M IC697MD IC697MDL

With its superior performance, power, and flexibility, GE FanucÕs Series 90TM-70 PLC provides a comprehensive solution thatÕs equal to the most demanding applications. With our CPX family of CPUs, the Series 90-70 offers more for your automation dollar, more computing power, more memory for your applications, and more communications and redundancy capabilities. And with a wide range of isolated and high-density VME analog I/O modules, the Series 90-70 provides even more flexibility for a variety of applications.
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring, 

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.