1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC697MDL253G

★★★★★Rated 4.4/5 Based on 9 ratings.

Rate your purchase of the IC697MDL253

SKU 2171223  UPC 0986784501837

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description

The IC697MDL253 is a 24 Volt AC, 32-Point Input module of the GE Fanuc Series 90-70. This module provides 4 isolated groups of 8 points each.  This allows each group of 8 points to be used on a different phase of the AC supply.  It comes with a 20ms filter and is compatible with a proximity switch. The input module is resistive and delivers 24 volts AC to the 32 points in the four isolated groups, each with eight points. Characteristics of the input are compatible with a diverse range of proximity switches. At the top of the input module, you will find LED indicators that will display the ON/OFF status of each point on the PLC.

To ensure accurate placement with a similar input module in the field, the module is mechanically keyed. The module does not require jumpers or DIP switches for user configuration. Configuration relies on MS-DOS or Microsoft Windows 95 or Windows NT operating systems and rides on TCP/IP protocol or via the SNP port. The programming software is normally installed on a programming device such as a Personal Computer, AT, IBM or PS/2. IC697MDL253 module is compatible with a myriad of input devices such as electronic proximity switches (both 2 and 3-wire), selector switches, limit switches as well as selector switches. Input current is normally 10mA when ON with a 2-mA leakage current when OFF. There is a preference for 3-wire proximity switches due to their provision of low voltage drop when ON and low current leakage in the OFF state.

This input module is designed to be compatible with 2-wire devices such as two-wire proximity switches which get their power from signal connections. It’s important to note that each type must be examined for compatibility in both ON and OFF states. Each module comes with a mechanical key ring to provide a fool proof functionality that prevents unintentional substitution of one module model for another in a slot. During field wiring, a wire from the source of power to the input power terminal for each group is required. The detachable field terminal board accepts wires sizes ranging from #22 (0.36mm2) to #14(2.10mm2). If they are of the same size, 2 wires can be terminated on one lug. 

Wiring procedures:

Firstly, switch off power before removal or installation or installation of terminal boards. You can access the jackscrew that secures the terminal in place by opening the hinged door on the module. The terminal board is then removed by turning the jackscrew counter clockwise until it’s full disengaged. Once this step is complete, swinging it out.

The terminal board accommodates wire ranges from AWG #22 right through AWG#14.  A maximum insulation diameter of .135 inches should not be exceeded when using AWG#14. For a perfect connection, two wires can be terminated on any terminal, provided they are of the same size. The terminal board is crafted to accommodate a maximum of 40 AWG #14 (2.10mm2) wires. Wire markers should be placed approximately 8 inches from the terminal end if AWG #14 are to be used. The space provides ample room for closing of the hinged door.

After all connections are completed, secure the wire bundle tightly using cable ties. A door label insert comes with every module to indicate circuit wiring information of the module. There’s a slot provision for insertion of the label on the hinged door. The outside label is color coded for quick identification of voltage type. Blue indicates low voltage while Red indicates high voltage. For ideal ventilation, leave a 6-inch clearance above and below the rack grill.

Technical Specifications

Rated Voltage: 24 volt AC
Number of Inputs:    32 Inputs (4 Isolated groups of 8)
Input Current: 10 mA
Current Required: 0.30 Amps
Freq: 47 to 63 Hz
DC Power: No

 

24 Volts ac Input (32) IC697M IC697MD IC697MDL

The CIMPLICITY Control programmer is designed to the IEC-1131 international standard. Version 2.0 and higher provides both relay ladder diagram (RLD) and sequential function chart (SFC) programming. Future developments will include Function Block Diagram (FBD), Structured Text (ST), and Instruction List (IL) editors. And, of course, CIMPLICITY Control can import your existing programs for Series 90-70 PLCs.
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring, 

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.