1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC697CGR935-CB

★★★★★Rated 4.6/5 Based on 19 ratings.

Rate your purchase of the IC697CGR935

SKU 2172064  UPC 0799705795068

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description


The IC697CGR935 module is a one slot controller in the GE Fanuc series, which permits fluctuating point calculations mandatory for CPU redundancy applications. The IC697CGR935 module in the Redundancy System is used as the controller. There are two control methods to note when using the IC697CGR935. In the GHS process, several single bus networks with one redundant controller are used in each synchronized PLC. When using the GDB process, multiple I/O networks are used with single or double buses in each synchronized PLC. Each control method can be easily activated and used without difficulty. In the IC697CGR935 module, the memory board delivers data, and program memory is included with the module. The IC697CGR935 can be operated remotely or by the three position RUN/STOP switch. Positioned on the front of the module are the LEDs, which specify the status of the CPU.

Installation of the IC97CGR935 module should not be attempted without referring to the appropriate Programmable Controller Installation and Hot Standby CPU Redundancy Manual. The battery should be connected to one of the module’s battery connectors. The key switch should be positioned to MEMORY PROTECT OFF, and there should be no rack power. Once module is installed in slot 1 of rack 0, power is turned on. The top LED should blink indicating that the IC697CGR935 module is powered up. Once the diagnostic is finished effectively, the top left LED stays on while the second and third LED will be off. The MEMORY PROTECT LED which is the fourth LED, is off because the key switch is in off position.  Programming is now ready for the CPU. The CPU can be programmed regardless of the placement of the key. Once the program has been confirmed, the toggle switch can be positioned in the appropriate operational mode.

Technical Specifications

Module Type: Single Slot CPU
Operating Temperature:   0 to 60 deg C (32 to 140 deg F)
Battery Shelf Life: 5 years at 20 deg C (68 deg F)
Inputs and Outputs: 12K each (any mix)
Serial Ports: 3
Current Required: 3.1 Amps nominal

 

 
In Stock! IC697CGR Redundant Dual Bus CPU IC697C IC697CG IC697CGR

A range of models with 4, 8, even 9 times the performance of the original Series 90-70 CPU are available. And, every one includes hardware floating point, not a slow software emulation.
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Battery, Configuration, Datasheet, Emerson, Firmware, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring, 

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.