1-919-535-3180
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-919-535-3180

Mon-Fri 8AM-5PM EST

[email protected]

IC693NIU004-AA

★★★★★Rated 4.7/5 Based on 11 ratings.

Rate your purchase of the IC693NIU004

SKU 2171004  UPC 0770072590654

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description

The IC693NIU004 is a GE Fanuc 90-30 series Ethernet Network Interface Unit.  This operates as an Ethernet Global Data station (EGD), exchanging input and output data, status and control data over the network. The unit comes with 8 LEDs, an ethernet restart push button, 3 port connectors, and a shield ground connection tab. The Mac Address label can be located on the outside of the module. The IC693NIU004 ENUI comes with 8 LEDs.  The EOK, LAN, STAT and PS port indicate the status of the module. The other four LEDs are linked to the two RJ-45 ports. The power supply LED is not related to the ethernet ports but only indicates the presence of traffic through the serial ports of the module’s power supply. The EOK, LAN and STAT LEDs can be On/OFF Blinking slow or Blinking fast. These indicate the status of the Ethernet interfaces, traffic at the Ethernet ports (LAN LED) and that an exception event has occurred. Every RJ-45 ports comes with 2 LEDs just as you would find on a PC’s RJ-45 port. The one labelled LINK/ACT comes on when the link is physically present and blinks when traffic is detected on that port. The other indicator labeled 100Mbps comes on to indicate that the connection is 100Mbps

The ethernet restart push button has 2 functions: performing the LED test and restart. Pressing the Ethernet restart push button will have the effect of disrupting ethernet communications, this includes any communication to other devices attached to the embedded switch. When the Ethernet restart pushbutton is pressed, the 7 LEDs come on simultaneously. One should ensure that the LEDs go OFF and ON. The interface then performs a restart. Power diagnostics run and interface’s software is restarted to operational state.

The RS-232, 6-pin, RJ-11 port is for connecting a terminal or terminal emulator to access the station manager software on the ethernet interface. The Station Manager feature is used for testing and troubleshooting Ethernet communications. Its use is, however, optional. A IC693CBL316A cable is used for connecting the terminal, emulator or software loader to the ethernet. The user can find 2 RJ-45 Ethernet ports on the NIU. One or both may be attached to other ethernet devices. Each port automatically senses data rate (10Mbps or 100Mbps), half or full duplex and cabling arrangement: either straight through or crossover. Cables used to connect to the ENUI can be either shielded or unshielded, direct or crossover. It should be noted that the two ethernet ports should not be connected to the same device as this will lead to duplication of packets. Before the Ethernet NIU is used on the network, it must be configured using the CIMPLICITY Machine Edition Logic Developer software. This is used for:

  • Assigning an IP address to the ENUI
  • Defining subnet mask, default gateway and name server address
  • Setting up Ethernet Global Data Exchange messaging between the ENIU and controller(s)

Installing the Ethernet NIU in the CPU Baseplate

  • Ensure that the baseplate power is turned OFF.
  • Align the module with slot 1 and the connector. Tilt the module up so the top rear hook of the module engages the slot on baseplate.
  • Swing the module down until the connectors mate and the locking lever on the bottom of the module snaps into place, engaging the baseplate notch.
  • Do Check the module to be sure that it is properly seated.
  • Connect one or both Ethernet ports on the Ethernet Interface to the network.
  • Restore power to the baseplate.

Technical Specifications

Module Type:  Ethernet Remote I/O Interface
Number of Slots: 1 (single slot)
Backplane Support:   CPU Slot
Protocol Support: CIMPLICITY Machine Edition
Ethernet Ports:    2 RJ-45
Internal Power: N/A

 

In Stock! ETHERNET NETWORK INTERFACE IC693N IC693NI IC693NIU

GE FanucÍs Series 90-30 PLCs are a family of controllers, I/O systems, and specialty modules designed to meet the demand for a versatile industrial control. The variety and flexibility of I/O and specialty modules make automation integration easy. There are 14 powerful CPUs to choose from, over 100 different I/O module types, a wide range of intelligent modules, high level communications options, and a variety of bus interfaces.
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Buy, Configuration, Datasheet, Emerson, Manual, Price, Repair, Specification, Troubleshoot, Wiring, 

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.