GE / IP FANUC Series 90/30 In Stock
IC693MDL930
SKU 2176200 UPC 0246834891845
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC693MDL930 IC693MDL930AIC693MDL930BIC693MDL930CIC693MDL930-CAIC693MDL930DIC693MDL930EIC693MDL930FIC693MDL930GIC693MDL930HIC693MDL930JIC693MDL930KIC693MDL930LIC693MDL930-LTIC693MDL930MIC693MDL930-RR
Common misspellings:
- 1C693MDL930
- IC693MD1930
- IC693MDL93o
- IC693MDL930
Technical Specifications for IC693MDL930
| Manufacturer | GE Fanuc |
|---|---|
| Series | Series 90-30 |
| Part Number | IC693MDL930 |
| Product Type | Output Module |
| Output Channels | 8 |
| Compatibility | Series 90-30 PLCs |
| Slots | 1 |
| Output Switching Capacity | 4 Amps |
| DC Operating Voltage | 5 to 30 Volts DC |
| AC Operating Voltage | 5 to 250 Volts AC |
Product Description
The GE Fanuc IC693MDL930 is a 4 Amp Isolated Relay Output module. Designed for the Series 90-30 Programmable Logic Controller, this module provides 8 normally-open relay circuits. These enable the user to control output loads. Each circuit has a 4-amp output switching capacity. Each output point on the module is isolated from the other points and each point has a separate common power output terminal.
The relay output module is able to control a variety of load devices. This includes but is not limited to indicators, motor starters and solenoids. To operate the field devices connected to this module, the user needs to supply either AC or DC power. On the top of the module there are two horizontal rows of green LEDs that indicate the ON/OFF status of each point. There are eight LEDs in each row. As the IC693MDL930 only has 8 relay circuits, the bottom row is not used. The top row, which is labelled A1, indicates the status of points 1 through 8.
There is an insert that sits between the inner surface and outer surface of the hinged door on the module. On the outer left edge, the insert is colored red. This indicates that it is a high-voltage module. When the door is closed, the inner surface facing the inside of the module has circuit wiring information. On the outside surface, circuit identification information can be recorded. Users who want to implement this module for their industrial applications can do so with any Series 90-30 PLC system. The relay output module may be installed in any I/O slot of either a 5-slot or 10-slot baseplate.
Technical Specifications
| Rated Voltage: | 24 volts DC or 120/240 volts AC |
| # of Outputs: | 8 |
| Freq: | 50/60 Hz with AC |
| Output Current: | 4 Amps per circuit |
| Output Voltage Range: | 5 to 30 volts DC, 5 to 250 volts AC |
| DC Power: | Yes |
The IC693MDL930 module is rated for 24 Volts DC and 120/240 Volts AC. For DC power, the operating voltage range is from 5 to 30 Volts DC, and for AC power, the operating voltage range is 5 to 250 Volts AC (at 50 to 60 Hertz). The field side to logic side isolation on the IC693MDL930 module is 1500 Volts. The maximum load rating for the IC693MDL930 module is 20 Amps for UL installation. The minimum load is 10 milliamps and the maximum inrush current is 5 Amps. The maximum on and off response times are both 15 milliseconds. The internal current consumption from the 5 Volts backplane power source is 6 milliamps when all of the outputs are on. The internal current consumption from the 24 Volts backplane is 70 milliamps when all of the outputs are on. The operating temperature range for the IC693MDL930 module is 0 to 50 degrees Celsius.
Technical Information
|
Rated Voltage |
24 volts DC, 120/240 VAC (nominal - see the following table for exceptions) |
|
Operating Voltage |
5 to 30 volts DC |
|
|
5 to 250 VAC, 50/60 Hz |
|
Outputs per Module |
Eight isolated outputs |
|
Isolation: |
|
|
Field to Backplane and to Frame Ground |
250 VAC continuous; 1500 VAC for 1 minute |
|
Point to Point |
250 VAC continuous; 1500 VAC for 1 minute |
|
Maximum Load |
4 Amps resistive maximum per output |
|
|
2 Amps pilot duty per output |
|
|
20 Amps maximum per module for UL installations Maximum Load depends on the ambient temperature as shown below |
|
Minimum Load |
10mA |
|
Maximum Inrush |
5 Amps |
|
On Response Time |
15ms maximum1 |
|
Off Response Time |
15ms maximum1 |
|
Power Consumption |
6mA (all outputs on) from 5 volt bus on backplane |
|
|
70mA (all outputs on) from relay 24V bus on backplane |
|
1 When this module is used with DC power supply IC695PSD040 or PSD140, special precautions should be taken because dropouts in the source voltage will be seen by this module and may cause relay dropouts. |
|
Troubleshooting
Troubleshooting IC693MDL930
Troubleshooting information is available on IC693MDL930’s website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC693MDL930
PDF Supply can repair your IC693MDL930 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC693MDL930? Answer: The IC693MDL930 is a 4 Amp Isolated Relay Output module for the GE Fanuc Series 90-30. It provides 8 normally-open relay circuits for controlling output loads provided by the user.
- Question: What is the output switching capacity for each circuit? Answer: 4 amps.
- Question: What can the relay outputs control? Answer: They can control motor starters, solenoids, and indicators.
- Question: What kind of power does the IC693MDL930 use? Answer: Power to operate IC693MDL930 must be supplied by the user and be either AC or DC power.
- Question: Are there fuses on this module? Answer: No
- Question: What is the rated voltage for IC693MDL930? Answer: 24 volts DC or 120/240 volts AC
- Question: What is the operating voltage for IC693MDL930? Answer: 5 to 30 volts DC or 5 to 250 volts AC, 50/60 Hz
- Question: What should I do if my IC693MDL930 is not working correctly? Answer: The product may need repair if your IC693MDL930 is not working correctly,
For more information on the IC693MDL930 Isolated Relay Output Module of the GE 90-30 Series, please see the Datasheet Manual.
|
Version |
Date |
Description |
|
IC693MDL930L |
May 2015 |
Change in fab color from Green to Blue. No change in form-fit- functionality. |
|
IC694 MDL930C |
Jan 2015 |
Updated modules are RoHS converted product with applicable exemptions. |
|
IC693/IC694 MDL930A |
Aug. 2008 |
Initial release. |
|
IC693MDL930K / IC694MDL930B |
Jun. 2013 |
Hardware update to resolve component obsolescence issue. No changes to features, functions or compatibility. |
|
IC693MDL930J / I C694MDL930A |
Aug. 2008 |
Initial release. |
Common related search terms: BuyDatasheet, Emerson, Manual, Price, Repair, Specification, Troubleshoot, Wiring,
