GE / IP FANUC Series 90/30 In Stock
IC693CPU352
SKU 2170039 UPC 044765976521
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC693CPU352 IC693CPU352-BBIC693CPU352-BCIC693CPU352-BDIC693CPU352-CDIC693CPU352-CEIC693CPU352-DEIC693CPU352-DFIC693CPU352-DGIC693CPU352-DHIC693CPU352-DJIC693CPU352-DKIC693CPU352-EKIC693CPU352-FKIC693CPU352-Programming SoftwareIC693CPU352-SoftwareIC693CPU352-CAIC693CPU352-LTIC693CPU352-RR
Common misspellings:
- 1C693CPU352
- IC693CPU352
Technical Specifications for IC693CPU352
| Manufacturer | GE Fanuc |
|---|---|
| Series | Series 90-30 |
| Part Number | IC693CPU352 |
| Product Type | CPU Module |
| Processor Speed | 25 Megahertz |
| Baseplate | CPU Baseplate |
| Voltage Input Rating | 5 Volts DC |
| Current Input Rating | 910 milliamps |
| Operating Mode | Run Mode, Stop Mode |
| Operating Temperature | 32 to 140 degrees Fahrenheit |
Product Description
The IC693CPU352 is a single slot CPU module manufactured by GE Automation and Controls for the Series 90/30 PLC system. The total number of Baseplates for each system is 8, which includes one baseplate for CPU, and seven remote and expansion. The load requirement of the Power Supply is 890mA from a +5Volts DC supply. The processor type is an 80386EX with a processing speed of 25Mhz. The optimum operating temperature for the system is between 0 degrees and 60 degrees Celsius (32 degrees and 140 degrees Fahrenheit). This specification is also referred to as the ambient temperature. The typical rate of scanning is 0.22milliseconds for every 1K logic (I.e., Boolean contacts).
Since the release of version 9.0 firmware, the maximum program memory for the user is 240K Bytes. However, the effective available size of the program memory for the user depends on configured amounts for configurable types of word memory. The discrete input and output points are 2048 each, 4096 bits for internal coils, 1280 bits for global memory, 256 bits for temporary output coils, 128 bits total (%S, %SB, %SA, %SC which have 32 bits for each) as references for system status. There are %R (Register Memory), %AI (Analog Inputs), %AQ (Analog Outputs), all configurable in increments of 128 words.
There are more than 2000 numbers of Timers/Counters, and there are also Shift Registers present. There are three serial ports built-in, which support RTU slave and SNP or SNPX slave, and SNP or SNPX master or slave, and Serial Input/output (on port 1 and port 2). Communications support LAN (multidrop supported), Ethernet, Profibus, FIP, GBC, GCM+ option modules. Flash memory and RAM are the available storage memory types. The Logicmaster configuration and programming software support CPU352.
Technical Specifications
| Processor Speed : | 25 MHz |
| I/O Points : | 2048 |
| Register Memory : | 240KBytes |
| Floating Point Math: | Yes |
| 32 BIT system | |
| Processor: | 80386EX |
The IC693CPU352 CPU from GE Fanuc is a Series 90-30 CPU module. It is designed to function at the center of a programmable logic controller or PLC from the Series 90-30 product line. In a Series 90-30 PLC, the IC693CPU352 CPU module is installed in a special CPU baseplate, and the PLC can contain as many as 7 additional baseplates which are remote baseplates or expansion baseplates. The voltage input rating of the IC693CPU352 CPU module is 5 Volts DC while its current rating is 910 milliamps. The maximum processor speed of this CPU is 25 Megahertz. The IC693CPU352 CPU module can operate at full power in a temperature range between 32 and 140 degrees Fahrenheit or 0 and 60 degrees Celsius.
The GE Fanuc Series 90-30 IC693CPU352 CPU module comes with 3 serial ports for communication, and it supports the RTU slave protocol, the SNP slave protocol, and the SNPX slave protocol. This CPU dissipates about 4.55 Watts of heat during operation. Option modules can be connected to the IC693CPU352 CPU module to allow it to communicate through different networks. These option modules include Profibus, Ethernet, FIP, GBC, GCM+, and multi-drop LAN modules. The IC693CPU352 CPU module is capable of scanning 1 KB of logic approximately every 0.22 milliseconds. There is a shield ground connector on the bottom of the CPU module that allows it to be protected. The operating modes supported by the IC693CPU352 CPU module are the Run mode and the Stop mode, and the users can select the mode that they want with a keyswitch.
Technical Information
CPU Type Single slot CPU module
Total Baseplates per System 8 (CPU baseplate + 7 expansion and/or remote)
Load Required from Power Supply 890 milliamps from +5 VDC supply
Processor Speed 25 MegaHertz
Processor Type 80386EX
Typical Scan Rate .22 milliseconds per 1K of logic (Boolean contacts)
User Memory (total) 240K (245,760) bytes, starting with firmware release 9.0. Note: Actual size of available user program memory depends on the amounts configured for the %R, %AI, and %AQ configurable word memory types (described below). Pre-9.0 firmware supported 80K bytes of fixed memory.
Discrete Input Points - %I 2,048
Discrete Output Points - %Q 2,048
Discrete Global Memory - %G 1,280 bits
Internal Coils - %M 4,096 bits
Output (Temporary) Coils - %T 256 bits
System Status References - %S 128 bits (%S, %SA, %SB, %SC - 32 bits each)
Register Memory - %R Configurable in 128 word increments, from 128 to 16,384 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver. 2.2 or later, or VersaPro version 1.0 or later.
Analog Inputs - %AI Configurable in 128 word increments, from 128 to 8,192 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver 2.2 or later, or VersaPro version 1.0 or later.
Analog Outputs - %AQ Configurable in 128 word increments, from 128 to 8,192 words with DOS programmer, and from 128 to 32,640 words with Windows programmer Ver. 2.2 or later, or VersaPro version 1.0 or later.
System Registers (for reference table
viewing only; cannot be referenced in user logic program) 28 words (%SR)
Timers/Counters >2,000 (depends on available user memory)
Shift Registers Yes
Built-in Serial Ports 3 (one uses connector on PLC power supply). Supports SNP/SNPX slave (on all three ports) and RTU slave and Serial I/O (on Ports 1 and 2). Requires CMM module for CCM and PCM module for RTU master.
Communications LAN – Supports multidrop. Also supports Ethernet, FIP, Profibus, GBC, GCM, and GCM+ option modules.
Override Yes
Battery Backed Clock Yes
Interrupt Support Supports the periodic subroutine feature.
Type of Memory Storage RAM and Flash
PCM/CCM Compatibility Yes
Floating Point Math Support Yes. Hardware-based (uses built-in math coprocessor)
Troubleshooting
Troubleshooting IC693CPU352
Troubleshooting information is available on IC693CPU352's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC693CPU352
PDF Supply can repair your IC693CPU352 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC693CPU352? Answer: The IC693CPU352 is a single-slot Central Processing Unit (from the GE Fanuc Series 90-30) with 2 built-in serial ports. This unit is the "brains" of the PLC and is where most of the calculations take place.
- Question: What's the first thing you should do when testing your IC693CPU352? Answer: When you attach the IC693CPU352 to a 5 or 10 slot rack and power it up, you should be checking for an OK light.
- Question: What if I do not have an OK light after I have powered it up? Answer: If you don't have an OK light, then you won't be able to follow through with the test. The lack of an OK light indicates, right from the start, there is something wrong with your IC693CPU352.
- Question: What is this initial test showing? Answer: You're basically turning on the configuration and logic in this processor in order to set it to run mode. You want to see that this is a good working processor.
- Question: With what software should I test my IC693CPU352? Answer: You can test your IC693CPU352 with Proficy Machine Edition.
- Question: What will I need to test my IC693CPU352? Answer: All you will need is your IC693CPU352, a 5 or 10 slot rack, and a power supply.
- Question: If I think there is a problem with my processor, what should I do? Answer: You should, first, make sure that when you turn on the memory on/off protection switch, the RUN light comes on and then let the processor run overnight (or even 2-3 days). This is to check that it's able to sustain itself in run mode. (You want to make sure it doesn't fail or fall out of run mode for any reason.) If it does fail or fall out of run mode, then you can try reading the faults or errors through the Proficy Machine Edition software. It may give you enough information to help you fix the problem.
- Question: If I can't figure out how to fix my IC693CPU352, what is my next step? Answer: PDF Supply can repair your IC693CPU352 for you.
- Question: Things you should also be testing: Answer: You should make sure that both ports are working by plugging into them and making sure the LED lights come on when you do plug into them.
For more information on the IC693CPU352 Central Processing Unit of the GE 90-30 Series, please see the Datasheet Manual.
|
Rel. |
Ver. |
Date |
IPI |
Upgrade Kit |
New Features |
Problems Resolved |
|
EK |
11 |
1-Apr |
GFK-1126ag |
N/A |
|
Hardware Upgrade - Fatal Fault Sometimes Occurs when Powering up from Flash |
|
DK |
11 |
Oct-00 |
GFK-1126ad |
44A739385-G08 |
|
Rotate Right and Rotate Left functions do not handle error condition correctly |
|
Time of Day clock at power-up may not operate |
||||||
|
Error when run-mode storing, loading, or verifying exactly 50 blocks in run mode |
||||||
|
Fatal Fault retry does not work correctly for some faults |
||||||
|
|
||||||
|
DJ |
10 |
Sep-00 |
GFK-1126ac |
44A739385-G07 |
IC693DSM314 support added |
User Flash Write and Erase Failure |
|
Local Logic Programs with VersaPro 1.10 |
PLC can Automatically go to Run Mode |
|||||
|
Reboot after Fatal Fault |
Retentive Contact Previous Values Table not being cleared |
|||||
|
Drum Sequencer function |
|
|||||
|
|
|
|||||
|
DH |
9.1 |
Jul-99 |
GFK-1126y |
44A739385-G06 |
|
AI & AQ Above Default Values |
|
Embedded Serial Ports with Rev.9.00 and 9.01 Firmware |
||||||
|
Load File of Size 1528 Bytes |
||||||
|
C Program with Code Area Greater Than 64K Bytes |
||||||
|
|
||||||
|
DG |
9 |
Jan-99 |
GFK-1126x |
44A739385-G05 |
Break-free SNP |
SNP Master mode on CPU Ports |
|
GFK-1126w |
Online Changes to Reference Tables |
|||||
|
|
Read from Flash |
|||||
|
|
|
|||||
|
DF |
9 |
Oct-98 |
GFK-1126u |
44A739385-G04 |
Software Floating Point |
Keyswitch Configured as RUN/STOP Switch |
|
User Memory Totals 240K bytes |
Storing IC693CMM321 Configuration with Windows PLC Programming Software |
|||||
|
Sequential Event Recorder |
RET_PBLOCK_LIST |
|||||
|
|
Service Request #7 |
|||||
|
|
|
|||||
|
DE |
8.1 |
May-98 |
GFK-1126t |
82A1071-MS10-000-A1 |
Demko Agency approval |
|
|
CE |
8.1 |
Dec-97 |
GFK-1126s |
|
C Programming |
Loading Default Program with Windows Programming Software |
|
IC693 SFC Programming Supports SFC in Subroutines and Multiple Actions per Step (up to 8) |
||||||
|
|
||||||
|
CD |
8 |
Sep-97 |
GFK-1126r |
|
|
Excessive Battery Drain |
|
BD |
8 |
Aug-97 |
GFK-1126p |
|
|
|
|
BC |
8 |
Apr-97 |
GFK-1455 |
|
C Programming |
ALT-S Run Mode Store of Periodic Subroutine |
|
Model Number Checks Removed |
HHP Write to Flash or EEPROM with MS-DOS Programmer Connected |
|||||
|
Generic String Output on CPU Ports |
Watchdog Timer Timeout (both ports active) |
|||||
|
RTU Slave Protocol |
|
|||||
|
Keyswitch Configurable as User Memory Protection Switch |
|
|||||
|
|
|
|||||
|
BB |
7 |
Feb-97 |
GFK-1126n |
|
|
Watchdog Timer Timeout |
Common related search terms: BatteryBuy, Configuration, Datasheet, Emerson, Firmware, Manual, Price, Repair, Specification, Troubleshoot, Wiring,
