GE / IP FANUC Series 90/30 In Stock
IC695ALG628
RX3i ALG628 Analog
SKU 2178226 UPC 0101254208652
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC695ALG628 IC695ALG628-AAIC695ALG628-BAIC695ALG628-CAIC695ALG628-DAIC695ALG628-EAIC695ALG628-FBIC695ALG628-GBIC695ALG628-HCIC695ALG628-HDIC695ALG628-LT
Common misspellings:
- 1C695ALG628
- IC695A1G628
- IC695ALG62b
- IC695ALG628
Product Description
The IC695ALG628 is an 8/4 Channel, Non-Isolated, Differential, Voltage/Current, HART, Analog Input module from the GE Fanuc RX3i Series. This Module provides 8 single-ended or 4 differential inputs. Module IC695ALG628 has 2 internal HART modems. See specifications for this unit on IC695ALG628's website page.
Technical Specifications
| Module Type: | Analog Input w/HART comms |
| Number of Inputs: | 8 single-ended or 4 differential |
| Internal Power: | 3.3V: 600mA; 5V: 450 mA |
| Number of Slots: | 1 (single slot) |
| Current Range: | 0-20 mA, 4-20 mA, +/-20 mA |
| Voltage Range: | +/-10V, 0-10V, +/-5V, 0-5V,1-5V |
Technical Information
Specifications
|
Input Ranges |
Current: 0 to 20mA, 4 to 20mA, ±20mA Voltage: ±10V, 0 to 10V, ±5V, 0 to 5V, 1 to 5V |
||||
|
Backplane Power Requirements |
ALG608: ALG616: ALG626: ALG628: |
200 mA maximum @ 5.0V +5% / -2.5%, 200 mA maximum @ 3.3V +5% / -3% 350 mA maximum @ 5.0V +5% / - 2.5%, 200 mA maximum @ 3.3V +5% / - 3% 400 mA maximum @ 5.0V +5% / - 2.5%, 200 mA maximum @ 3.3V +5% / - 3% 260 mA maximum @ 5.0V +5% / - 2.5%, 200 mA maximum @ 3.3V +5% / - 3% |
|
||
|
Power Dissipation within Module |
IC695ALG608: IC695ALG626: |
2.58 W maximum; IC695ALG616: 4.50 W maximum; IC695ALG628: |
4.25 W maximum 2.83 W maximum |
||
|
Thermal Derating |
IC695ALG608 and ALG616: no derating IC695ALG628: no derating Module IC695ALG626 has no thermal derating in voltage mode. For thermal derating for module IC695ALG626 in current mode, refer to page 4. |
||||
|
Resolution |
24-bit ADC converted to Floating Point or Integer |
||||
|
Input Data Format |
Configurable as floating point IEEE 32-bit or 16-bit integer in a 32-bit field |
||||
|
Filter Options |
8Hz, 12Hz, 16Hz, 40Hz, 200Hz, 500Hz |
||||
|
HART Communications |
Version 5.0 HART protocol supported on modules IC695ALG626 and IC695ALG628. |
||||
|
Input Impedance |
>100 kï— voltage inputs |
||||
|
Current Input Resistance |
249 ï— ±1% |
||||
|
Open Circuit Detection time |
1 second maximum |
||||
|
Overvoltage |
±60 VDC continuous, maximum |
||||
|
Overcurrent |
±28mA continuous, maximum |
||||
|
Normal Mode Noise Rejection in dB |
|
At 50Hz |
At 60Hz |
||
|
8 Hz filter |
85 |
85 |
|||
|
12 Hz filter |
85 |
85 |
|||
|
16 Hz filter |
35 |
62 |
|||
|
40 Hz filter |
3 |
6 |
|||
|
200 Hz filter |
0 |
0 |
|||
|
500 Hz |
0 |
0 |
|||
|
Common Mode Noise Rejection |
120dB minimum @ 50/60 Hz with 8 Hz filter 110dB minimum @ 50/60 Hz with 12 Hz filter |
||||
|
Channel-Channel DC Crosstalk |
-80 dB minimum (single ended mode) -80 dB minimum (differential mode, grounded common) -60 dB minimum (differential mode, floating common) |
||||
|
Isolation Voltage terminal block to backplane/chassis |
Opto-isolated, transformer isolated 250 VAC continuous/1500 VAC for 1 minute |
||||
|
Analog Module Scan Time (in milliseconds)
Configured Filter
8 Hz filter 12 Hz filter 16 Hz filter 40 Hz filter 200 Hz filter 500 Hz filter [with filtering and rate detection disabled] Configured Filter
8 Hz filter 12 Hz filter 16 Hz filter 40 Hz filter 200 Hz filter 500 Hz filter [with filtering and rate detection disabled] |
The module scan for analog signals can consist of up to four acquisition cycles. Each cycle includes a specific set of channels. Total Scan Time depends on the number of acquisition cycles in the scan, the configured filter option, and whether channels are analog or HART. |
|||||||
|
Number of Acquisition Cycles in the Scan (IC695ALG608/616/626/628- Ex and earlier) |
||||||||
|
1 |
2 |
3 |
4 |
|||||
|
Analog |
HART |
Analog |
HART |
Analog |
HART |
Analog |
HART |
|
|
121 |
128 |
241 |
254 |
362 |
380 |
482 |
506 |
|
|
81 |
88 |
161 |
174 |
242 |
260 |
322 |
346 |
|
|
61 |
68 |
121 |
134 |
182 |
200 |
242 |
266 |
|
|
21 |
28 |
41 |
54 |
62 |
80 |
82 |
106 |
|
|
5 |
12 |
9 |
22 |
14 |
32 |
18 |
42 |
|
|
3 |
N/A |
5 [6] |
N/A |
7 [9] |
N/A |
9 [12] |
N/A |
|
|
Number of Acquisition Cycles in the Scan (C695ALG608/616/626/628- Fx and later) |
||||||||
|
1 |
2 |
3 |
4 |
|||||
|
Analog |
HART |
Analog |
HART |
Analog |
HART |
Analog |
HART |
|
|
122 |
124 |
247 |
248 |
367 |
375 |
494 |
500 |
|
|
82 |
85 |
164 |
169 |
247 |
255 |
329 |
337 |
|
|
62 |
65 |
127 |
130 |
188 |
191 |
252 |
258 |
|
|
25 |
26 |
50 |
50 |
76 |
72 |
100 |
93 |
|
|
6 |
12 |
12 |
17 |
19 |
24 |
26 |
32 |
|
|
3 |
N/A |
7 [6] |
N/A |
11 [9] |
N/A |
15 [12] |
N/A |
|
|
HART Data Scan Time (in seconds) |
The HART data scan can consist of up to four acquisition cycles (similar but asynchronous to the analog scan time). Each cycle includes a specific set of channels. Total HART scan time depends on the number of channels enabled for HART within a specific set of channels, number of retries, enabling/disabling of slot variables, and use and configuration settings of pass-thru commands. |
|||||||
|
Channels in Group Enabled for HART: |
Each HART Data channel updates every: |
|||||||
|
One |
0.7 second (typical) |
|||||||
|
Two |
1.9 seconds (typical) |
|||||||
|
Three |
3.0 seconds (typical) |
|||||||
|
Four |
4.0 seconds (typical) |
|||||||
|
Calibrated Accuracy In the presence of severe RF interference (IC 801-3, 10V/M), accuracy may be degraded by ±1.5% of range. |
From 13°C – 33°C: ±5V, ±10V, ± 20 mA: 0.05% of range. 0 to 10V, 0 to 5V, 1 to 5V, 0 to 20 mA: 0.1% of range. 4 to 20 mA: 0.125% of range. |
|||||||
|
From 0°C – 60°C: 0 to 10V, 0 to 5V, 1 to 5V: 0.2% of range. 0 to 20 mA: 0.25% of range. 4 to 20 mA: 0.3125% of range. ±5V, ±10V: 0.1% ±20 mA: 0.125% of range. |
||||||||
|
Calibration Interval |
12 months typical to meet accuracy specifications over time. Offset can be applied as a periodic calibration adjustment. |
|||||||
Troubleshooting
Troubleshooting IC695ALG628
Troubleshooting information is available on IC695ALG628's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC695ALG628
PDF Supply can repair your IC695ALG628 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC695ALG628? Answer: The IC695ALG628 is an 8/4 Channel, Non-Isolated, Differential, Voltage/Current, HART, Analog Input module from the GE Fanuc RX3i Series.
- Question: What does IC695ALG628 provide? Answer: This module provides 8 single-ended or 4 differential input channels.
- Question: What does IC695ALG628 feature? Answer: This module features HART version 5.0 communications capability on each channel.
- Question: How many HART modems does IC695ALG628 have? Answer: This module has 2 internal HART modems.
- Question: What happens in single-ended mode? Answer: In single-ended mode, 4 single-ended channels are multiplexed into each HART modem.
- Question: What happens in differential mode? Answer: In differential mode, 2 differential channels are multiplexed into each HART modem.
- Question: For configuration, at what ranges can the analog input channels be set? Answer:
- Current: 0 to 20 mA, 4 to 20 mA, +/- 20 mA
- Voltage: +/- 10 V, 0 to 10 V, +/- 5 V, 0 to 5 V, 1 to 5 V
- Question: For channels that use HART communications, what must the configuration be? Answer: It must be in the 4-20mA range.
- Question: What should I do if my IC695ALG628 is not working properly? Answer: Your IC695ALG628 may need repair.
For more information on the IC695ALG628 8/4 Channel, Non-Isolated, Differential, Voltage/Current, HART, Analog Input Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.
Release History
|
Version |
Firmware Revision |
Description |
|
IC695ALG608-HD, IC695ALG616-HD, IC695ALG626-HD, IC695ALG628-HD |
2.08 |
Provided resolution to issues introduced in firmware version 2.00 (- FB):
|
|
IC695ALG608-HC, IC695ALG626-HC, IC695ALG628-HC |
2.06 |
IC695ALG626-FB, IC695ALG628-FB, IC695ALG608-FB (and later) provides the wrong device ID to RX3i PNS (IC695PNS001) and IC695CEP001 modules causing a configuration mismatch. |
|
IC695ALG608-GB, IC695ALG616-GB, IC695ALG626-GB, IC695ALG628-GB |
2.00 |
|
|
IC695ALG608-FB, IC695ALG616-FB, IC695ALG626-FB, IC695ALG628-FB |
2.00 |
|
|
IC695ALG608-EA, IC695ALG616-EA, IC695ALG626-EA, IC695ALG628-EA |
1.01 |
Label change only. No change in functionality, performance or compatibility. |
|
IC695ALG608-DA, IC695ALG616-DA, IC695ALG626-DA, IC695ALG628-DA |
1.01 |
Modified the terminal block detector switch to increase the size of the switch lever. The increased size of the switch lever allows additional tolerance to assure contact with the terminal block actuator. |
|
IC695ALG608-CA, IC695ALG616-CA, IC695ALG626-CA, IC695ALG628-CA |
1.01 |
Updated Hardware |
|
Version |
Firmware Revision |
Description |
|
IC695ALG608-BA, IC695ALG616-BA, IC695ALG626-BA, IC695ALG628-BA |
1.01 |
Updated Hardware |
|
IC695ALG608-AA, IC695ALG616-AA, IC695ALG626-AA, IC695ALG628-AA |
1.01 |
Initial Release |
Common related search terms: BatteryBuy, Configuration, Datasheet, Dimension, Emerson, Fanuc, Firmware, GE, GE-Fanuc, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
