GE / IP FANUC Series 90/30 In Stock
IC695ALG600
RX3i ALG600 Analog
SKU 2176026 UPC 0347129212533
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC695ALG600 IC695ALG600-AAIC695ALG600-ABIC695ALG600-BCIC695ALG600-CCIC695ALG600-DCIC695ALG600-DDIC695ALG600-EEIC695ALG600-LT
Common misspellings:
- 1C695ALG600
- IC695A1G600
- IC695ALG6o0
- IC695ALG60o
- IC695ALG600
Technical Specifications for IC695ALG600
| Manufacturer | GE Fanuc |
|---|---|
| Series | Versamax |
| Part Number | IC695ALG600 |
| Product Type | Thermocouple Input Module |
| Number of Channels | 8 |
| Input Resolution | 11 to 16 bits |
| Power Dissipation | 5.4 Watts |
| Backplane Power Requirement | 400 mA at 5V, 350 mA at 3.3V |
| RTD Cable Impedance | 25 Ohms |
| RTD Wire Length | 1000 feet |
Product Description
The IC695ALG600 is an 8-Channel, Thermocouple, Resistance, Current/Voltage, RTD, Universal, Analog Input module from the GE Fanuc RX3i Series. The IC695ALG600 provides 8 general purpose input channels and 2 Cold Junction Compensation (CJC) channels. This module must be located in an RX3i Universal Backplane. See specifications for this unit on IC695ALG600's website page.
Technical Specifications
| Module Type: | Universal Analog |
| Number of Inputs: | 8 general purpose |
| Internal Power: | 3.3V: 350mA; 5V: 400 mA |
| Number of Slots: | 1 (single slot) |
| Range (ohms): | 0 to 250/500/1000/2000/3000/4000 |
| Power Dissapation: | 5.4W max |
The IC695ALG600 Thermocouple Input Module is a universal analog input module manufactured by GE Fanuc. It has 8 general-purpose input channels and 2 CJC channels. All the inputs are divided into 2 equal groups. The IC695ALG600 Thermocouple Input Module offers 6 analog to digital filter frequencies which can be individually configured to each channel. Its diagnostic facilities have on-board error checking, open-circuit detection, short-circuit detection, and module fault reporting. Some of the features of the module include full auto-calibration, on-board error checking, user-defined scaling, module fault reporting, terminal block insertion or removal detection, configurable software filters, and configurable interrupts. It provides temperature readings in Celsius or Fahrenheit.
The IC695ALG600 Thermocouple Input Module is compatible with the CIMPLICITY machine edition software. It is a completely software-configurable module that provides easy configuration and commissioning processes. It provides 2 isolated groups of input channels. The power dissipation within the module is 5.4 Watts. It offers floating-point user scaling. This IC695ALG600 module can be installed in an RX3i universal backplane. However, it cannot be located in an expansion or remote backplane. Its group of input channels can be individually-configured to be thermocouple inputs, RTD inputs, resistance inputs, or current and voltage inputs. It offers 11 to 16 bits of input resolution. The input resolution of the module depends on the A/D filter frequency and configuration range. It is recommended to use CJC sensors for the thermocouple input configurations. It can automatically check for the presence of the terminal block. This module comes with flash memory for easy future upgrades.
Technical Information
Specifications
|
Backplane Power Requirements |
300 mA maximum @ 5.0V 320 mA maximum @ 3.3V |
|
|
Power Dissipation within Module Thermal Dissipation |
5.4 watts maximum |
|
|
LEDs |
One green LED to indicate the module status One bi-color green/yellow LED to indicate the field status One bi-color red/green LED to indicate the terminal block status |
|
|
Per Channel Acquisition Time (Each group scanned independently) |
10 msec @ 1000 Hz, 13 msec @ 200 Hz, 27 msec @ 40 Hz, 67 msec @ 16 Hz, 87 msec @ 12 Hz, 127 msec @ 8 Hz |
|
|
Channel Update Time |
The sum of the channel acquisition times for a bank of 4 channels plus one of the following if applicable: 1. RTD Lead resistance measurement time (equals channel acquisition time) 2. CJC acquisition time 7 msec. |
|
|
Input resolution |
11 to 16 bits, depending on configured range and A/D filter frequency. |
|
|
Inputs in Ohms |
Resistance |
0-250, 0-500, 0-1000, 0-2000, 0-3000, 0-4000 |
|
Platinum 385 |
100, 200, 500,1000 |
|
|
Platinum 3916 |
100, 200, 500,1000 |
|
|
Nickel 672 |
120 |
|
|
Nickel 618 |
100,200, 500,1000 |
|
|
Nickel-Iron 518 |
604 |
|
|
Copper 426 |
10 |
|
|
RTD Inputs |
Copper 426 |
-100 to 260°C |
|
Nickel 618 |
-100 to 260°C |
|
|
Nickel 672 |
-80 to 260°C |
|
|
Nickel-Iron 518 |
-100 to 200°C |
|
|
Platinum 385 |
-200 to 850°C |
|
|
Platinum 3916 |
-200 to 630°C |
|
|
Thermocouple Inputs |
Type B |
300 to 1820°C |
|
Type C |
0 to 2315°C |
|
|
Type E |
-270 to 1000°C |
|
|
Type J |
-210 to 1200°C |
|
|
Type K |
-270 to 1372°C |
|
|
Type N |
-210 to 1300°C |
|
|
Type R |
0 to 1768°C |
|
|
Type S |
0 to 1768°C |
|
|
Type T |
-270 to 400°C |
|
|
Voltage Inputs |
-10V to +10V, 0V to +10V, 0V to +5V, 1V to +5V, -50mV to +50mV, -150mV to +150mV |
|
|
Current Inputs |
-20mA to +20mA, 4 to 20mA, 0 to 20mA |
|
|
Configurable Input Filter |
8 Hz, 12 Hz, 16 Hz, 40 Hz, 200 Hz, 1000 Hz |
|
|
Scaling |
Floating point user scaling. |
|
|
Max RTD Cable Impedance |
25 ohm |
|
|
RTD Wire Length |
1000 ft max w/settling time of 1mSec |
|
|
Input Impedance |
>1M ohm for TC/V/RTD |
|
|
Current Input Resistance |
249 ohm +/- 1% |
|
|
Open circuit detection time |
5 seconds max. Open circuit detection is available for all configurations except +/- 20mA current, 0-20mA current, and +/-10V voltage. |
|
Max Overvoltage |
+/-14.5VDC continuous |
|
Max Overcurrent |
28 mA continuous |
|
Normal Mode Noise Rejection |
95 dB minimum @ 50/60 Hz with 8 Hz filter 85 dB minimum @ 50/60 Hz with 12 Hz filter |
|
Common Mode Noise Rejection |
120dB minimum @ 50/60 Hz with 8 Hz filter 110dB minimum @ 50/60 Hz with 12 Hz filter |
|
Settling time to 5% of Full Scale (notch filter dependent) |
<80 mS |
|
Calibrated Accuracy at 25°C |
Better than 0.1% of range (except 10 ohm CU RTD) Accuracy depends on A/D filter, data format, input noise, and ambient temperature. |
|
Calibration interval |
12 months typical to meet accuracy specifications over time. Module will allow for user offset to be applied as a periodic calibration adjustment. |
|
Input Offset Drift with Temperature |
3.0 milliohm/°C maximum 2.0 uV/°C maximum |
|
Gain Drift with Temperature |
50 ppm/°C typical (90 ppm/°C maximum) |
|
Module error over Full Temp range |
0.5% of range typical (depends on range) 1.0% of range maximum |
|
Module Scan Time (notch filter dependent) |
(Assumes 2 ADC’s running in parallel, no CJC or lead resistance) 10 ms per Channel × 4 Channels = 40 ms (1K Hz filter) 127 ms per Channel × 4 Channels = 508 ms (8 Hz filter) Channels that are disabled are not scanned, shortening scan time. |
|
Module conversion method |
Sigma-delta |
|
Isolation Voltage channel to channel group to group terminal block to backplane/chassis |
Opto-isolated, transformer isolated +-12.5Vdc channel to channel Tc/V/I/RTD 250 VAC continuous/1500 VAC for 60 seconds 250 VAC continuous/1500 VAC for 60 seconds |
Troubleshooting
Troubleshooting IC695ALG600
Troubleshooting information is available on IC695ALG600's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC695ALG600
PDF Supply can repair your IC695ALG600 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC695ALG600? Answer: The IC695ALG600 is an 8-Channel, Thermocouple, Resistance, Current/Voltage, RTD, Universal, Analog Input module from the GE Fanuc RX3i Series.
- Question: What does IC695ALG600 provide? Answer: This module provides 8 general purpose input channels and 2 Cold Junction Compensation (CJC) channels. The inputs are divided into 2 equal groups of 4.
- Question: Individual configuration for each channel using the Machine Edition software can be what? Answer:
- Any combination of up to 8 channels of voltage, current, thermocouple, RTD, and resistance inputs
- Thermocouple Inputs: B,C, E, J, K, N, R, S, T
- RTD Inputs: PT 385/3916, N 618/672, NiFe 518, CU 426
- Resistance Inputs: 0 to 250/ 500/ 1000/ 2000/ 3000/ 4000 Ohms
- Current: 0-20 mA, 4-20 mA, +/- 20 mA
- Voltage: +/- 50 mV, +/- 150 mV, 0-5 V, 1-5 V, 0-10 V, +/- 10 V
- Question: What is one thing you will need to test IC695ALG600? Answer: You will need a high-density terminal strip (IC694TBB032).
- Question: What do I need to know about the high-density terminal strip? Answer: You should make sure the lever on it is in the upright-most position, which will turn the LED green to let you know you are fully connected. If it is red or you don't have a light, then you know something is wrong.
- Question: What 3 things are you looking for when testing your channels? Answer:
- an accurate channel
- an active channel
- a stable channel
- Question: What should I do if my IC695ALG600 is not working properly? Answer: Your IC695ALG600 may need repair.
For more information on the IC695ALG600 8-Channel, Thermocouple, Resistance, Current/Voltage, RTD, Universal, Analog Input Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.
Release History
|
Release |
Hardware Update |
Firmware Revision |
|
IC695ALG600-EE IC695ALG600CA-EE (conformal coat) IC695ALG600LT-EE (low temperature) |
This version of the product is a new HW/FW design to resolve obsolescence and comply with EU RoHS 2011/65/EU |
Primary: 2.00 Boot: 2.00 |
|
IC695ALG600-DD |
This version of the product contains an enhancement to the design that improves the tolerance of terminal block detection. |
Primary: 1.14 Boot: 1.10 |
|
IC695ALG600-DC |
Label change only. No change in functionality, performance or compatibility. |
Primary: 1.11 Boot: 1.10 |
|
IC695ALG600-CC |
Modified the terminal block detector switch to increase the size of the switch lever. The increased size of the switch lever allows additional tolerance to assure contact with the terminal block actuator. |
Primary: 1.11 Boot: 1.10 |
|
IC695ALG600-BC |
Improved noise immunity |
Primary: 1.11 Boot: 1.10 |
|
IC695ALG600-AB |
None |
Primary: 1.10 Boot: 1.10 |
|
Initial Release |
None |
Primary: 1.00 Boot: 1.00 |
Common related search terms: BatteryBuy, Configuration, Datasheet, Dimension, Emerson, Fanuc, Firmware, GE, GE-Fanuc, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
