1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC694PSM001

RX3i PSM001 Accessory

★ ★ ★ ★ ★ Rated 4.6/5 Based on 5 ratings.

Rate your purchase of the IC694PSM001
GE Intelligent Platforms / GE Fanuc - RX3i PacSystem - IC694PSM001

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

Other Available Revisions for the IC694PSM001 IC694PSM001-AAIC694PSM001-ABIC694PSM001-LT

Common misspellings:
  • 1C694PSM001
  • IC69APSM001
  • IC694PSMo01
  • IC694PSM0o1
  • IC694PSM00l
  • IC694PSM001

Product Description

The IC694PSM001 is a Power Sync and Measurement (PSM) module from the GE Fanuc RX3i Series. This module monitors two independent three-phase power grids.  See specifications for this unit on IC694PSM001's website page.

Technical Specifications

Module Type: Power Sync and Measurement   
Input Voltage Range 20 to 600 VAC
Freq Range: 40 to 70 Hz
Input Current Range: 0 to 7.5 Amps
# of Outputs:  1
Power Consumption:   190 mA from 5 V bus 

 

 

Technical Information

Specifications

 

PSM Module Power Requirements

Backplane Power Consumption

400 mA max. at 5 VDC

Total Power Dissipation

2.0 W max.

Isolation from Backplane

1500 VDC

Maximum number of PSM modules per RX3i system

No restrictions, as long as the power supply has sufficient capacity

Sync Relay Contacts

 

Two isolated relay outputs

General purpose: 125 VAC / 125 VDC maximum at 1 amp Lamp duty: 125 VAC / 125 VDC maximum at 1 amp

Pilot duty: 125 VAC / 125 VDC maximum at 0.35 amp

Switching speeds Turn-on time Turn-off time

 

20 ms

5 ms

Measurement Specifications

Three voltage inputs per grid

All voltage data is scaled in 0.1 VAC units.

Impedance:

>1 MΩ

Range

Low range High range

 

45–150 VAC RMS (120 VAC nominal)

120–690 VAC RMS (600 VAC  CAT IV; 690 VAC CAT III)

Frequency

30–70 Hz

Four current inputs per grid

All current data is scaled in 0.001 Amp units.

Impedance

<5 milliohms

Range

0–5 A RMS (5 A nominal)

Frequency

30–70 Hz

Phase difference between grids:

±180O

Measurement Accuracy 1

Voltage

0.2%

Current

0.2%

kW, kVAR, kVA

0.4%

kWH, kVARH, kVAH

0.4%

Power factor

1%

Frequency

0.01 Hz

Phase angle

0.1O

Terminal Assembly Input Terminal Ratings

Current

15 Amps continuous maximum

Voltage

690 VAC RMS

Sync Relay contacts

150 VAC/VDC at 1 Amp Resistive, maximum

Note: Actual contact ratings depend on load type. Refer to Sync Relay Contacts above.


 

Troubleshooting

Troubleshooting IC694PSM001

Troubleshooting information is available on IC694PSM001's website page; it also includes a datasheet user-manual and a wiring diagram.


Repair your IC694PSM001

PDF Supply can repair your IC694PSM001 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Customer Questions and Answers

  • Question:  What is an IC694PSM001?  Answer:  The IC694PSM001 is a Power Sync and Measurement (PSM) module from the GE Fanuc RX3i Series.
  • Question:  What does IC694PSM001 provide?   Answer:  IC694PSM001 monitors two independent three-phase power grids. 
  • Question:  What does the IC694PSM001 incorporate?   Answer:  This module incorporates advanced digital signal processor (DSP) technology to continuously process three voltage inputs and four current inputs for each grid.
  • Question:  What measurements are provided?   Answer:  Measurements include RMS voltages, RMS currents, RMS power, frequency and phase relationship between the phase voltages of both grids.
  • Question:  What calculations are performed?   Answer:  The PSM module performs calculations on each captured waveform, with the DSP processing the data in less than two-thirds of a power line cycle. 
  • Question:  What are some applications for the IC694PSM001?   Answer:  The PSM system can be used for applications such as:
    • Electrical power consumption monitoring and reporting
    • Fault monitoring
    • Generator control features for generator to power grid synchronization
    • Demand penalty cost reduction/load shedding
  • Question:  What does the PSM system consist of ?   Answer:  The PSM system consists of:
    • PSM Module
    • Terminal Assembly
    • Interface Cables
  • Question:  What should I do if my IC694PSM001 is not working properly?   Answer:  Your IC694PSM001 may need repair. 

For more information on the IC694PSM001 Power Sync and Measurement (PSM) module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual. 

Release History

 

 

Version

Firmware Revision

Date

 

Comments

IC694PSM001-AB

1.01

January 2013

Enhanced operation of sync relay feature as described below.

IC694PSM001-AA

1.00

December 2012

Initial release

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.