GE / IP FANUC Series 90/30 In Stock
IC694MDL916
RX3i MDL916 Digital I/O
SKU 2176303 UPC 0773055780998
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC694MDL916 IC694MDL916-AAIC694MDL916-LT
Common misspellings:
- 1C694MDL916
- IC69AMDL916
- IC694MD1916
- IC694MDL9l6
- IC694MDL916
Technical Specifications for IC694MDL916
| Manufacturer | GE Fanuc |
|---|---|
| Series | RX3i PACSystems |
| Part Number | IC694MDL916 |
| Product Type | Output Module |
| Output Type | Relay Outputs |
| Number of Outputs | 16 |
| Voltage Type | AC and DC |
| Supply Voltage | 0 to 250 Volts AC, 0 to 125 Volts DC |
| Output Voltage | 5 to 250 Volts AC, 0 to 125 Volts DC |
| Frequency | 47 to 63 Hertz |
Product Description
The IC694MDL916 is a 16-Point, 4 Amp, Isolated Relay Output module from the GE Fanuc RX3i Series. This module provides 16 Form A relays for controlling output loads. See specifications for this unit on IC694MDL916's website page.
Technical Specifications
| Rated Voltage: | 5/24/125 volts DC, 120/240 volts AC |
| # of Outputs: | 16 (isolated) |
| Freq: | 50/60Hz (A/C only) |
| Output Current: | 10mA per point max |
| Output Voltage Range: | 5 to 125VDC, 5 to 250 VAC |
| Power Consumption: | 300mA from 5V bus, 150mA from 24V relay |
The GE Fanuc IC694MDL916 output module is an RX3i PACSystems series output module with 16 output channels. It is a relay output module that supports point to point isolation. Its switching current rating is 4 Amps and its maximum backplane current draw rating is 300 milliamps. The IC694MDL916 relay output module is meant to be installed in an RX3i PACSystems programmable logic controller or PLC to allow the PLC to communicate with or control external field devices. This output module can be installed in any available slot that is designated for I/O modules in the PLC racks. The IC694MDL916 relay output module can be configured with either the Service Pack 2 or later versions of the Service Pack software, or the Machine Edition version of the Proficy software.
The GE Fanuc RX3i PACSystems IC694MDL916 16-point relay output module uses an external power supply, and it requires a supply voltage rating of 0 to 250 Volts AC or 0 to 125 Volts DC. Its supported output voltage ranges are 5 to 250 Volts AC or 0 to 125 Volts DC with a frequency range of 47 to 63 Hertz for both voltage ranges. The typical response time for the IC694MDL916 relay output module is about 10 milliseconds both when the module is being switched off and when it is being switched on. This module needs to be mounted on a terminal block that will host all of its wiring, and it is compatible with several different kinds of terminal blocks including standard spring and box-style terminal blocks and extended spring and box-style terminal blocks.
Technical Information
Specifications
|
Outputs per Module External Power Supply
Isolation Field to Backplane and to Frame Ground, Group to Group Power Consumption
Thermal Derating |
16 isolated Form A relay outputs 0 – 125VDC (5/24/125 VDC nominal) 0 – 250VAC (47 to 63 Hz), 120-240VAC nominal
250 VAC continuous; 1500 VAC for 1 minute.
300mA at 5VDC from backplane maximum (all outputs ON) 150mA at 24VDC from backplane relay power (all outputs ON) See next page |
|
Output Characteristics |
|
|
Output Voltage |
5 – 125VDC (5/24/125 VDC nominal) |
|
|
5 – 250VAC (47 to 63 Hz), 120-240VAC nominal |
|
Output Current |
10mA per point minimum |
|
|
4A for 5-250VAC maximum (resistive or general purpose) |
|
|
4A for 5-30VDC maximum (resistive) |
|
|
200mA for 125VDC (maximum resistive) |
|
|
2A pilot duty per output (5 to 30VDC, 5 to 250VAC) |
|
|
2A lamp load per output (5 to 30VDC, 5 to 250VAC) |
|
Output Voltage Drop |
0.3VDC maximum |
|
Output Leakage Current |
Not Applicable (open contact) |
|
Response Times (On/Off) |
10ms maximum (At nominal voltage excluding contact bounce) |
|
Switching Frequency |
20 cycles per minute maximum |
|
Protection |
None. External snubbers may be applied if necessary |
|
Relay Contact Life |
See chart on the next page |
|
Diagnostic Information |
Field side terminal block presence detection reported to CPU (for RX3i |
|
|
only) |
Troubleshooting
Troubleshooting IC694MDL916
Troubleshooting information is available on IC694MDL916's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC694MDL916
PDF Supply can repair your IC694MDL916 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC694MDL916? Answer: The IC694MDL916 is a 16-Point, 4 Amp, Relay, Output module from the GE Fanuc RX3i Series.
- Question: What does IC694MDL916 provide? Answer: This module provides 16 Form A relays for controlling output loads.
- Question: What is the output switching capacity? Answer: 4 Amps
- Question: The output points are set up how? Answer: Each output is islotated from the other points, and each has a separate common power output terminal.
- Question: What can the relay outputs control? Answer: The relay outputs can control a wide range of load devices such as: motor starters, solenoids, and indicators.
- Question: What does the red/green TB LED indicate? Answer: The red/green TB LED is green when the module removable terminal block is locked in place. It is red when the terminal block is not locked.
- Question: The red bands on the label show what? Answer: They show that IC694MDL916 is a high-voltage module.
- Question: What is the rated voltage of IC694MDL916? Answer: 5/24/125 volts DC, 120/240 volts AC (nominal)
- Question: What is the operating voltage of IC694MDL916? Answer: 5 to125 volts DC, 5 to 250 volts AC, 50/60 Hz
- Question: What is the ON/OFF Response Time? Answer:
- 10 ms maximum*
- *=When this module is used with DC power supply IC695PSD040 or PSD140, special precautions should be taken because dropouts in the source voltage will be seen by IC694MDL916 and may cause relay dropouts.
- 10 ms maximum*
- Question: What should I do if my IC694MDL916 is not working properly? Answer: Your IC694MDL916 may need repair.
For more information on the IC694MDL916 16-Point, 4 Amp, Relay, Output Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.
Release History
|
Release |
Comments |
|
IC693MDL916-AA, IC694MDL916-AA |
Initial Release |
Common related search terms: BatteryBuy, Configuration, Datasheet, Dimension, Emerson, Fanuc, Firmware, GE, GE-Fanuc, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
