GE / IP FANUC Series 90/30 In Stock
IC694MDL754
RX3i MDL754 Digital I/O
SKU 2176437 UPC 0353435386806
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC694MDL754 IC694MDL754-ABIC694MDL754-BCIC694MDL754-CCIC694MDL754-CDIC694MDL754-DDIC694MDL754-EDIC694MDL754-FDIC694MDL754AIC694MDL754-LT
Common misspellings:
- 1C694MDL754
- IC69AMDL754
- IC694MD1754
- IC694MDL75A
- IC694MDL754
Product Description
The IC694MDL754 is a 32-Point, 12/24 VDC, Electronic Short Circuit Protection (ESCP), Positive Logic, Output module from the GE Fanuc RX3i Series. This module provides 32 discrete output points. The outputs are positive logic or sourcing type outputs. See specifications for this unit on IC694MDL754's website page.
Technical Specifications
| Rated Voltage: | 12/24 volts DC |
| # of Outputs: | 32 (4 isolated groups of 8) |
| Freq: | N/A |
| Output Current: | 0.75A per point |
| Output Voltage Range: | 10.2 to 30VDC |
| Power Consumption: | 300mA from 5V bus |
Technical Information
Specifications:
|
Rated Voltage Output Voltage Range |
12/24 volts DC, nominal 10.2 to 30 volts DC |
|
Outputs per Module |
32 (two isolated groups of 16 outputs each) |
|
Isolation: |
|
|
Field to Backplane (optical) and to Frame Ground |
250 VAC continuous; 1500 VAC for 1 minute |
|
Group to Group |
250 VAC continuous; 1500 VAC for 1 minute |
|
Module ID |
0x059h |
|
Output Current |
0.75 Amps per point |
|
Power Consumption |
300 mA (maximum) from 5 volt bus on backplane; |
|
Thermal Derating |
No derating at 24VDC. At 30VDC, outputs are derated above 42 degrees C as shown below. |
|
External Power Supply |
+12 VDC to +30 VDC, 12/24 VDC nominal |
|
External Power Supply Current Required (not including load current) |
Module version –CC and later: 72 mA/group with all outputs commanded Off, 132 mA/group with all outputs commanded ON |
|
|
Module version –BC and earlier: 72 mA/group with all outputs commanded OFF, 100 mA/group with all outputs commanded ON |
|
Output Characteristics |
|
|
Inrush Current |
3 Amps supplied for 10ms without ESCP trip |
|
Output Voltage Drop |
0.3 volt DC maximum |
|
Steady-state overcurrent trip |
5 Amps typical per point |
|
Output Leakage Current |
0.1mA maximum |
|
On Response Time |
0.5ms maximum |
|
Off Response Time |
0.5ms maximum |
|
Protection |
Short-circuit protection, overcurrent protection, overtemperature protection, all with auto recovery. |
Troubleshooting
Troubleshooting IC694MDL754
Troubleshooting information is available on IC694MDL754's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC694MDL754
PDF Supply can repair your IC694MDL754 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Inrush Current For IC693MDL754 or IC694MDL754
Description
The inrush current for IC693MDL754 or IC694MDL754
Resolution
3A, 10 ms
Customer Questions and Answers
- Question: What is an IC694MDL754? Answer: The IC694MDL754 is a 32-Point, Positive Logic, 12/24 VDC, Electronic Short Circuit Protection (ESCP), Output module from the GE Fanuc RX3i Series.
- Question: What does IC694MDL754 provide? Answer: This module provides 32 discrete output points in 4 isolated groups of 8 each. Each group has its own common.
- Question: How can the module's groups be wired? Answer: Each group can be used to drive different loads. For example, one group might drive 12 VDC loads and the other might drive 24 VDC loads.
- Question: How does the module operate? Answer: The outputs are positive logic or sourcing type outputs and can switch user loads over the range of +12 to -24 VDC and can source a max current of 0.75A per point.
- Question: How is the module protected? Answer: Each point has electronic overcurrent/short circuit protection and generates an individual fault if either condition exists.
- Question: Is power available from this module? Answer: Power to provide current to the loads must be provided by the user.
- Question: 32 green LEDs indicate what? Answer: 32 green LEDs indicate the ON/OFF status of points 1 through 32.
- Question: The blue bands on the label let you know what? Answer: They let you know that IC694MDL754 is a low-voltage module.
- Question: Into what slot can IC694MDL754 be installed? Answer: This module can be installed in any I/O slot of an RX3i system. It must be used with an RX3i CPU (release 2.90 or greater).
- Question: What should I do if my IC694MDL754 is not working properly? Answer: Your IC694MDL754 may need repair.
For more information on the IC694MDL754 32-Point, Positive Logic, 12/24 VDC (ESCP), Output Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.
Release History
|
Release |
FW Version |
Date |
Comments |
|
IC694MDL754-FD |
1.20 |
May 2017 |
RoHS converted product with applicable exemptions. No change in form-fit-functionality |
|
IC694MDL754-ED |
1.20 |
Dec 2016 |
Resolves an issue found in version (-DD) related to field bulletin wherein outputs commanded ON may start oscillating if user supplied power is between 16VDC to 20VDC. As a result of this change, IC694MDL754-ED is not RoHS compliant. No change in form-fit-functionality. |
|
IC694MDL754-DD |
1.20 |
Jan 2016 |
Updated modules are RoHS converted product with applicable exemptions. No change in form-fit-functionality |
|
IC694MDL754-CD |
1.20 |
Mar 2009 |
Backward compatible with all previous versions. |
|
IC694MDL754-CC |
1.10 |
Feb 2008 |
Backward compatible with all previous versions. |
|
IC694MDL754-BC |
1.10 |
Nov 2005 |
Backward compatible with all previous versions. |
|
IC694MDL754-AB |
1.00 |
May 2005 |
Compatible with PACSystems RX3i CPU 3.0 firmware or later. |
|
IC694MDL754A |
1.00 |
Mar 2005 |
Initial Release. Compatible with PACSystems RX3i CPU 2.9 firmware only. |
Common related search terms: BatteryBuy, Configuration, Datasheet, Dimension, Emerson, Fanuc, Firmware, GE, GE-Fanuc, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
