1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC694MDL390-Emerson

★★★★★Rated 4.5/5 Based on 10 ratings.

Rate your purchase of the IC694MDL390

SKU 2176359  UPC 0362177932295

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description

The IC694MDL390 is a GE Fanuc 120/240 VAC, 2 Amp, 5-Point Isolated Output Module for the Rx3i PACSystem. It can be used to replace the IC697MDL341 discrete output module from series 90-70 PLCs. This particular module has five isolated outputs (versus the previous version’s 12 individually isolated outputs). The commons are not connected inside the module, and the output circuits can be used on different phases of the AC supply or powered from the same supply. User-supplied AC Power is required to operate the output-connected loads. AC power is the singular option as DC power is not compatible.

The IC694MDL390 module is equipped with individual outputs with 3 amp fuses. Furthermore, the RC snubber helps to prevent electrical noise that could occur on the line. A wide variety of incandescent and inductive loads can be handled by the IC694MDL390. The IC694MDL390 module has five LEDs that monitor the status of outputs. A red LED will turn ON if an output circuit fuse is faulty. Red bands situated on the label indicate high-voltage. Installation of this module is suitable for any I/O slot in an RX3i system. It should be configured as an 8-point output module with programs that reference the five least significant bits. Max load current is dependent on ambient temps as noted in the manual. Inrush current is 25 amps max for one cycle. Minimum load current is 100mA. Power consumption runs 110mA with all outputs ON from a 5V bus on the backplane.

Technical Specifications

Rated Voltage:   120/240 volt AC
# of Outputs: 5 (isolated)
Freq: 50/60 Hz
Output Current: 2 Amps max
Output Voltage Range:   85 to 264 VAC
Power Consumption:  110 mA from 5V bus

 

 

Part Number: IC694MDL390 / ic694mdl390
Mfr/Brand Name: GE Automation
Mfr Number: IC694MDL390 / ic694mdl390
Type: 120/240 volt AC, 2 amp, Isolated Output Module, 5 Points

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.