GE / IP FANUC Series 90/30 In Stock
IC694MDL350
RX3i MDL350 Digital I/O
SKU 2175233 UPC 0516930652375
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC694MDL350 IC694MDL350-AAIC694MDL350-BAIC694MDL350-CAIC694MDL350-DAIC694MDL350-LT
Common misspellings:
- 1C694MDL350
- IC69AMDL350
- IC694MD1350
- IC694MDL35o
- IC694MDL350
Technical Specifications for IC694MDL350
| Manufacturer | GE Fanuc |
|---|---|
| Series | RX3i PACSystems |
| Part Number | IC694MDL350 |
| Product Type | Output Module |
| Rated Voltage | 120/240 Volts AC |
| Outputs per Module | 16 |
| Output Voltage Range | 74 to 265V AC (47 to 63 Hz) |
| Inrush Current | 20 Amps per cycle |
| Operating Temperature | 0 to 60 degrees Celsius |
| Storage Temperature | -40 to 85 degrees Celsius |
Product Description
The GE Fanuc IC694MDL350 is a 120/240 Volt AC, 16 output module that provides 16 isolated output points. Unlike previous models, this module is strongly protected against transient electrical noise from the power line so it doesn’t need an external snubber. The 16 individual outputs can handle a wide variety of inductive and incandescent loads. Output loads require a user-supplied external AC power supply to operate. A DIP switch is located on the back side of the output module IC694MDL350 and is used to control output default mode. It can be set to Force Off or Hold Last State. To use this switch, the user must remove the module from the backplane.
On the front side of the module, indication LEDs helps the user monitor output use. These individually numbered LEDs indicate ON and OFF status and also monitors the terminal block. Additionally, there are two red bands on the door card that alert the user to the module’s high voltage. The IC694MDL350 can be connected to box-style, spring style, or extended versions of the terminal block. Extended terminal blocks offer extra shroud depth normally needed for field wiring to AC devices. Terminal blocks will need to be ordered separately. This module can work in any Rx3i system I/O slot; however, it must be used with a version 3.50 or greater RX3i CPU. It cannot be used with a 90-30 series PLC CPU.
Technical Specifications
| Rated Voltage: | 120/240 volts AC |
| # of Outputs: | 16 |
| Freq: | 50/60 Hz |
| Output Current: | 2A max per point, 5A max per module |
| Output Voltage Range: | 74 - 265 VAC |
| Power Consumption: | 315 mA from 5V bus |
The IC694MDL350 Output Module comes with LED indicators that show the on and off status of each output point of the module. It also features a terminal block LED indicator since this module can accommodate removable terminal blocks. When the “Terminal Block” LED indicator turns green, it means that the terminal block installed. When this LED turns red, then it means that no terminal block is present, or that the terminal block has been disconnected. There is a red band on top of the module’s door which means that it is a high-voltage output module. The GE Fanuc IC694MDL350 Output Module operates in a temperature range from 0 to 60 degrees Celsius and it can be stored in a temperature range from -40 to 85 degrees Celsius.
Technical Information
Specifications: IC694MDL350
|
Rated Voltage |
120/240 volts AC |
|
Output Voltage Range |
74 – 265VAC (47 to 63 Hz), 120/240VAC nominal |
|
Outputs per Module |
16 isolated |
|
Isolation |
|
|
Field to Logic Side |
250 VAC continuous; 1500 VAC for 1 minute |
|
Group to Group |
250 VAC continuous; 1500 VAC for 1 minute |
|
Power Consumption |
315 mA (with all outputs ON) from 5 volt bus on backplane |
|
Diagnostics |
Field side terminal block status reported to RX3i CPU |
|
Output Current |
Per Point: 2A max. @ 30°C, 1A max. @ 60°C |
|
(Linear derating) |
Per Module: 5A max. @ 30°C, 4A max. @ 60°C |
|
Output Characteristics |
|
|
Inrush Current |
20 Amps maximum for one cycle |
|
Minimum Load Current |
10 mA per point |
|
Output Voltage Drop |
1.5 volts maximum |
|
Output Leakage Current |
2 mA maximum |
|
On Response Time |
1/2 cycle maximum |
|
Off Response Time |
1/2 cycle maximum |
|
Fuses |
No internal fusing. Use of appropriate external fuses is |
|
|
recommended for short circuit protection. |
Troubleshooting
Troubleshooting IC694MDL350
Troubleshooting information is available on IC694MDL350’s website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC694MDL350
PDF Supply can repair your IC694MDL350 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC694MDL350? Answer: The IC694MDL350 is a 120/240 VAC 16-Point Isolated Output module. This module provides 16 individually isolated output points. The outputs can control a wide range of inductive and incandescent loads.
- Question: What does a RC snubber do for this module? Answer: It protects each input against transient electrical noise on the power line.
- Question: With what Terminal Blocks can the IC694MDL350 be used? Answer: The IC694MDL350 can be used with a Box-style (IC694TBB032), Extended Box-style (IC694TBB132), Spring-style (IC694TBS032), or Extended Spring-style (IC694TBS132) Terminal Block.
- Question: What do Extended terminal blocks do? Answer: They provide the extra shroud depth typically needed for field wiring to AC devices.
- Question: What does the TB LED green light mean? Answer: It means that the module's removable terminal block is locked in place.
- Question: What does the TB LED red light mean? Answer: It means that the module's terminal block is not locked in place.
- Question: Into what can the IC694MDL350 be installed? Answer: The IC694MDL350 can be installed in any I/O slot in an RX3i system. It must be used with RX3i CPU release date 3.50 or later.
- Question: What should I do if my module is not working? Answer: If your IC694MDL350 is not working, then your product may be in need of repair.
For more information on the IC694MDL350 Isolated Input Module of the GE RX3i Series, please see the Datasheet Manual.
Release History
|
Version |
Description |
|
IC694MDL350-CA Firmware revision: 1.20 |
Label change only. No change in functions, performance or compatibility. |
|
IC694MDL350-BA Firmware revision: 1.20 |
Hardware update to correct a manufacturing issue. |
|
IC694MDL350-AA Firmware revision: 1.20 |
Initial Release |
Common related search terms: BatteryBuy, Configuration, Datasheet, Dimension, Emerson, Fanuc, Firmware, GE, GE-Fanuc, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
