1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC694DSM324-AC

★★★★★Rated 4.6/5 Based on 5 ratings.

Rate your purchase of the IC694DSM324

IC694DSM324 In Stock! DSM324 motion controller module for the RX3i IC694D IC694DS IC694DSM PDFsupply

SKU 2178331  UPC 0799705793392

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description

The IC694DSM324 is a GE Fanuc motion controller module belonging to the Rx3i PACSystem. It’s a multi-axis module, which will support standard mode (follower control loop disabled) and follower mode (follower control loop enabled).

The modules come with electronic CAM functionality, an analog I/O port that is used for connection to a PC, and switch inputs for every servo axis. For programming and configuration purposes, the module uses a single point of connection with firmware being saved in flash memory and updated through the COMM port. Storage is non-volatile and can hold up to 10 programs as well as 40 subroutines. Furthermore, it comes with a powerful set of motion program instructions designed for use by 1 to 4 axes.

The IC694DSM324 is equipped with eight LED indicators for displaying the status of the module. The STATUS LED is usually ON, which means the device is working properly. If the LED goes out, this indicates an error and a non-functional module. During module configuration, the CONFIG LED is ON. The FSSB LED is ON when there are FSSB communications and BLINKS during setup. There are also axis-enabled LEDs that come ON when axis 1 to 4 drives are enabled.

The FSSB connector allows for fiber connection to servo amplifiers for command / instructions exchange and diagnostics. It normally has a protection cap to avoid damage. The RJ-11 COMM port is used for downloading of firmware updates. The module also comes with two ports for 24 VDC and 5 VDC power. Pre-manufactured cables come in 1 meter and 3 meter lengths. The IC694DSM324 should be connected to frame ground using the ground terminal located at the bottom of the module. The recommended grounding resistance should be 100 ohms or less. 

Technical Specifications

Module Type: Servo Motion
Number of Slots: 1 (single slot)
Backplane Support: Universal Backplane
Analog Inputs: 2
Analog Outputs:  2
Power Consumption:   1360 mA @ 5 VDC

 

 
DSM324 motion controller module for the RX3i IC694D IC694DS IC694DSM
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.