1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC694ALG542-Battery

★★★★★Rated 0/5 Based on ratings.

Rate your purchase of the IC694ALG542

Image of IC694ALG542

SKU 0  UPC 00

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description


The IC694ALG542 Analog Current/Voltage Module is manufactured by GE Fanuc for PACSystems RX3i. The advanced diagnostics offer a mixed I/O analog current/voltage with four differential input channels. Additionally, two single-ended output channels are available. The configuration for each channel can be completed with the Machine Edition software for any of the following ranges: (0 to +10 volts) unipolar, (-10 to +10 volts) bipolar, 0 to 20 mA, or 4 to 20 mA. Moreover, input channels can be configured for an enhanced mode at 4-20 mA. Each individual output can be configured to either a Hold Last State or at the low end of the power range. This comes into effect if the system’s power in interrupted. Outputs are configurable as well. These can operate in ramp mode on command from the application program. In this mode, the output channel ramps to a new value over time, rather than an immediate new value. High and low limits can be set for each channel as well as an open wire fault reported to the CPU for each individual output channel.


Features available on the IC694ALG542 module include open circuit detection for each input in the enhanced range, configurable scaling and offsets per channel, and alarm detection and reporting per channel. Module fault reporting is also available on this module with support of full diagnostic point fault contacts in the logic program. Firmware upgrades are fully supported.


During installation and to ensure correct functioning, this module requires 150mA plus loop current from a user supplied 24Vdc external source. The module supports the insertion and removal from an RX3i universal backplane. This module has an update rate of 2ms. 

Technical Specifications

Module Type: Analog Mixed I/O
Backplane Support:  No restrictions
# of Slots 1 (single slot)
Voltage Range: 0 to +10V, -10 to +10V
Current Range: 0 to 20mA, 4 to 20mA
Power Consumption:    95mA @ 5V, 150mA @ 24VDC external

 

 

RX3i Efficiency combination analog module, 4 in voltage/current and 2 out voltage/current with 16 bit resolution and advanced diagnostics.
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.