GE / IP FANUC Series 90/30 In Stock
IC694ALG392
RX3i ALG392 Analog
SKU 2175000 UPC 0799705802384
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC694ALG392 IC694ALG392-AAIC694ALG392-BBIC694ALG392-BCIC694ALG392-CDIC694ALG392-CEIC694ALG392-LT
Common misspellings:
- 1C694ALG392
- IC69AALG392
- IC694A1G392
- IC694ALG392
Technical Specifications for IC694ALG392
| Manufacturer | GE Fanuc |
|---|---|
| Series | RX3i PACSystems |
| Part Number | IC694ALG392 |
| Product Type | High-Density Analog Output Module |
| User Supply Voltage (Nominal) | 24 Volts DC |
| External Supply Voltage Range | 20 to 30 Volts DC |
| Number of Output Channels | 8 Single-ended Output Channels |
| Output Current Range | 4 to 20 milliamps and 0 to 20 milliamps |
| Output Voltage Range | 0 to 10 Volts DC and -10 to 10 Volts DC |
| LEDs | “MODULE OK” and “USER SUPPLY” |
Product Description
The IC694ALG392 is an 8 Channel, Current/Voltage, Analog Output Module from the GE Fanuc RX3i Series. This module provides up to 8 single-ended output channels with current loop outputs and/or voltage outputs. See specifications for this unit on IC694ALG392's website page.
Technical Specifications
| No. of channels: | 8 |
| Voltage Range: | 0 to +10 V, -10 to +10 V |
| Current Range: | 0-20 mA, 4-20 mA |
| Update Rate: | 8 msec |
| Output Load: | 5 mA max |
| Power Consumption: | 110 mA @ +5VDC, 315 mA @ +24VDC Isolated |
The GE Fanuc IC694ALG392 High-Density Analog Output Module is an 8-channel current/voltage analog output module designed for the GE RX3i PACSystems control system. This module provides 8 single-ended output channels that are capable of accepting either current loop outputs or voltage outputs. Selection between current or voltage outputs can be achieved via software configuration. The outputs can be configured for a 0 to 10 Volts DC (unipolar), -10 to +10 Volts DC (bipolar), 0 to 20 milliamps, or 4 to 20 milliamps output range. Each IC694ALG392 Module output is capable of converting 15 to 16 bits of binary data from the CPU to analog data for output devices. The IC694ALG392 Module refreshes/updates every output channel every 8 milliseconds. The operators can switch between the current mode and the voltage mode via easy and simplified software configuration. The IC694ALG392 Module reports open-wire faults and other fault conditions to the CPU in the current mode.
The IC694ALG392 Output Module must receive its 24 Volts DC operating power from an external user-supplied power source, which can be connected to the TB1 connector on the left side of the backplane or directly to the module’s terminal block. It supports 24 Volts DC user-supplied power, which supplies a 20 to 30 Volts DC voltage range. The IC694ALG392 Module has a maximum backplane current draw of 110 milliamps at 5 Volts DC and 315 milliamps of rated power consumption at 24 Volts DC. Each of the IC694ALG392 Module’s outputs is factory-calibrated and they do not require any additional field calibration. The IC694ALG392 Module can be installed in any I/O slot on the RX3i PLC rack and it can be configured with the Proficy Machine Edition configuration software. The IC694ALG392 Module has a front-panel “MODULE OK” LED and a “USER SUPPLY” LED which are powered by the 5 Volts DC backplane power bus.
Technical Information
Specifications:
|
Number of Output Channels |
1 to 8 selectable, single–ended |
|
Output Current Range |
4 to 20 mA and 0 to 20 mA |
|
Output Voltage Range |
0 to 10 V and –10 V to +10 V |
|
Calibration |
Factory calibrated to .625 μA for 0 to 20 mA; 0.5 μA for 4 to 20 mA; and .3125 mV for voltage (per count) |
|
User Supply Voltage (nominal) |
+24 VDC, from user supplied voltage source |
|
External Supply Voltage Range |
20 VDC to 30 VDC |
|
Power Supply Rejection Ratio (PSRR) Current Voltage |
5 μA/V (typical), 10 μA/V (maximum) 25 mV/V (typical), 50 mV/V (maximum) |
|
External Power Supply Voltage Ripple |
10% (maximum) |
|
Internal Supply Voltage |
+5 VDC from PLC backplane |
|
Update Rate |
8 milliseconds (approximate, all eight channels) Determined by I/O scan time, application dependent. |
|
Resolution: |
4 to 20mA: 0.5 μA (1 LSB = 0.5 μA) |
|
|
0 to 20mA: 0.625 μA (1 LSB = 0.625 μA) |
|
|
0 to 10V: 0.3125 mV (1 LSB = 0.3125 mV) |
|
|
-10 to +10V: 0.3125 mV (1 LSB = 0.3125 mV) |
|
Absolute Accuracy: 1 |
|
|
Current Mode |
+/-0.1% of full scale @ 25°C (77°F), typical +/-0.25% of full scale @ 25°C (77°F), maximum +/-0.5% of full scale over operating temperature range (maximum) |
|
Voltage Mode |
+/-0.25% of full scale @ 25°C (77°F), typical +/-0.5% of full scale @ 25°C (77°F), maximum +/-1.0% of full scale over operating temperature range (maximum) |
|
Maximum Compliance Voltage |
VUSER –3 V (minimum) to VUSER (maximum) |
|
User Load (current mode) |
0 to 850 Ω (minimum at VUSER = 20 V, maximum 1350 Ω at VUSER = 30 V) (Load less than 800 Ω is temperature dependent.) |
|
Output Load Capacitance (current mode) |
2000 pF (maximum) |
|
Output Load Inductance (current mode) |
1 H |
|
Output Loading (voltage mode) Output load Capacitance |
5 mA (2 K Ohms minimum resistance) (1 μF maximum capacitance) |
|
Isolation, Field to Backplane (optical) and to frame ground |
250 VAC continuous; 1500 VDC for 1 minute |
|
Power Consumption |
110 mA from +5 VDC PLC backplane supply |
|
|
315 mA from +24 VDC user supply |
|
1In the presence of severe RF interference, accuracy may be degraded to 1% full scale (FS) for current outputs and 3% FS for voltage outputs. |
|
Troubleshooting
Troubleshooting IC694ALG392
Troubleshooting information is available on IC694ALG392's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC694ALG392
PDF Supply can repair your IC694ALG392 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC694ALG392? Answer: The IC694ALG392 is an 8 Channel, Current/Voltage, Analog Output module from the GE Fanuc RX3i Series.
- Question: What does IC694ALG392 provide? Answer: This module provides up to 8 single-ended output channels with current loop outputs and/or voltage outputs.
- Question: How can each output channel be set up? Answer:
- Each output channel can be set up using the configuration software for any of these ranges:
- 0 to +10 volts (unipolar)
- 10 to +10 volts (bipolar)
- 0 to 20 milliamps
- 4 to 20 milliamps
- Each output channel can be set up using the configuration software for any of these ranges:
- Question: Each channel is capable of converting how many bits of binary data to an analog output? Answer: 15-16 bits (depending on the range selected)
- Question: How often are all 8 channels updated? Answer: They are updated every 12 milliseconds.
- Question: What happens in current modes? Answer: In current modes, the module reports an Open Wire fault to the CPU for each channel.
- Question: What happens when system power is interrupted? Answer: When systems power is interrupted, the module can go to a known last state. As long as external power is applied to the module, each output will maintain its last value or reset to zero, as configured.
- Question: Into what slot can IC694ALG392 be installed? Answer: IC694ALG392 can be installed in any I/O slot of an RX3i system.
- Question: What should I do if my IC694ALG392 is not working properly? Answer: Your IC694ALG392 may need repair.
For more information on the IC694ALG392 8 Channel, Current/Voltage, Analog Output Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.
Release History
|
Version |
Date |
Description |
|
|
IC693ALG392-CF IC694ALG392-CD |
1.60 |
May 2012 |
See “Problems Resolved by Version 1.60.” |
|
IC693ALG392-BE IC694ALG392-BC |
1.01 |
Feb. 2010 |
See GFK-2557B. |
|
IC693ALG392-BD IC694ALG392-BB |
1.00 |
Jan. 2009 |
Updated processor and D/A converter. IC693ALG392-BB or later is not compatible with a Series 90-30 Hand-held Programmer. |
|
IC693ALG392-C |
1.00 |
Feb. 2005 |
ATEX approval for Group 2, category 3 applications. |
|
IC694ALG392-AA |
1.00 |
Jul. 2004 |
Initial product release |
|
IC693ALG392-B |
1.00 |
Oct. 1995 |
CE certification |
|
IC693ALG392-A |
1.00 |
n/a |
Initial release |
Common related search terms: BatteryBuy, Configuration, Datasheet, Dimension, Emerson, Fanuc, Firmware, GE, GE-Fanuc, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
