1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC694ALG391-Emerson

★★★★★Rated 4.7/5 Based on 11 ratings.

Rate your purchase of the IC694ALG391

SKU 2178264  UPC 0799705802407

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

Product Description


The GE Fanuc IC694ALG391 is a two channel analog current output module. Each of the two channels is capable of converting 12 bits of binary data for field devices. Additionally, each output can be set up using a jumper to construct varying signals, 0 to 20 mA or 4 to 20 mA. Each output can be set as a less exact voltage source, and the range is made with a jumper or resistor on the terminals as decided by the user.

Though an external source of isolated +24 VDC is vital for power for the module, it can be linked via the TB1 connector on the backside or directly to the terminal block. Both are effective methods for this model. However, if the user needs to preserve hold last state operation during a loss of backplane power, then an outside source is needed. An update rate of 5 milliseconds on both channels is application dependent but available.

When installing the GE Fanuc IC694ALG391, a good grade of twisted, shielded instrumentation cable should be used to lessen noise and capacitive loading. Each channel’s range is set with jumpers on the module terminals, and for voltage operation, a 250 Ohm resistor can be used in place of a voltage jumper if desired. Note: If the output default jumper is installed on module terminals 11 and 13, then both outputs will default, using the low end of their range. If the output jumper is not installed, both outputs will hold the last valid output value that was acknowledged. However, this route requires an external +24 VDC power supply.

Technical Specifications

No. of channels: 2
Voltage Range: 1-5 V, 0-5 V
Current Range: 0-20 mA, 4-20 mA
Update Rate: 5 msec
Output Load: 5 mA max
Power Consumption:   30 mA @ +5VDC,  120 mA @ +24VDC Isolated

 

 

Part Number: IC694ALG391 / ic694alg391
Mfr/Brand Name: GE Automation
Mfr Number: IC694ALG391 / ic694alg391
Type: Output Module Analog, Current, 2 channels.

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.