GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

Mon-Fri 8AM-5PM EST

STXMBS002

Rated 4.4/5 Based on 11 ratings.

Rate your purchase of the STXMBS002
GE STXMBS002 RSTi Modbus RS-485 slave Network Adaper.  24VDC powered, expandable to 32 modules. GE-I

SKU 2174067  UPC 0799705805439

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

New

$902

10 In Stock

✓  2 Year PDF Supply Warranty

*Need a Specific Revision?

Ships .

New Surplus

$722

Save $180

7 In Stock

✓  3 Year PDF Supply Warranty

*What is New Surplus?

Ships .

GE STXMBS002 RSTi Modbus RS-485 slave Network Adaper. 24VDC powered, expandable to 32 modules. GE-IP

Technical Information

The GE Fanuc STXMBS002 RSTi Modbus RS-485 Slave Network Adapter has been specifically designed to be used for serial RS-485 data communications protocols where it serves as the main interface between an RSTi PLC system and other equipment with the Modbus RS-485 protocol. The main benefit of using the serial Modbus RS-485 communication protocol is that it allows for a real-time data transfer between the RSTi Programmable Logic Controller (PLC) and up to 64 independent devices (32 drivers and 32 receivers). The maximum cable length for connecting the GE Fanuc STXMBS002 RSTi Modbus RS-485 Slave Network Adapter to other devices is 1200 meters (3937 feet). This network adapter board has complete compatibility with both the ASCII and RTU communication modes. It always acts as a slave device in a master-slave framework, that is, it acts as the passive receiver that will only respond to the master processor when there is some information that needs to be passed along.

 

The GE Fanuc STXMBS002 RSTi Modbus RS-485 Slave Network Adapter uses a 24 Volts DC rated power source and it is expandable with up to 32 additional modules. Because it is a small and lightweight solid-state electronic board, the GE Fanuc STXMBS002 RSTi Modbus RS-485 Slave Network Adapter is very easy to install in pre existing electrical enclosures, with the only prerequisite being that these enclosures should not be exposed to direct sunlight, high humidity, and temperatures outside the range of -20 to 60 degrees Celsius (-4 to 140 degrees Fahrenheit). The GE Fanuc STXMBS002 RSTi Modbus RS-485 Slave Network Adapter should only be installed, maintained, or repaired by qualified electrical or electronic technicians, in order to guarantee trouble-free operation and extended operating lifespan.

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.