IC660ELB922

Troubleshooting

Troubleshooting IC660ELB922

Troubleshooting information is available on IC660ELB922's website page; it also includes a datasheet user-manual.  

Repair your IC660ELB922
PDF Supply can repair your IC660ELB922 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.

Installing Genius PCIM Cards in Computer and using TestGENI Program

Description: The Genius PCIM card provides a computer with a full-function bus controller for Genius I/O networks. The card is available in an is a, VME and PC-104 form factor and a PCI version is underdevelopment for 2002.
The newer IC660ELB921 and IC660ELB922 versions of the PCIM have replaced the IC660ELB906 two-slot PCIM and the new ELB921 is significantly lower priced when compared to the ELB906. New single-slot cards have a single DIP switch to define the I/O control port address for 14 bytes of EEPROM data containing the GENI setup data. EEPROM data defaults to port 3E4, memory D000 and SBA 31 at 153 KB Std for the first channel.
Many software packages were based on the old ELB906 card and they do not describe the EEPROM switch. The PCIM manual, GFK-0081, defines the switches backwards on page 3-2 (Up arrow should be up away from the board). The factory default settings of hex 222 may also conflict with address 220 used by 16-bit sound card support in some motherboards. A control port setting of hex 3E2 (1-8=O O O O O C C C where Closed is Down toward card) is recommended.

Resolution: Software is required to change the EEPROM setup data. The DPCIMCFG program that ships with the PCIM has no diagnostics and may not run on fast computers. The TestGENI program is recommended to setup and test any PCIM card. TestGENI is a 16-bit DOS program that runs under Windows 95 and 98, but it cannot access hardware under Windows NT/2000/XP. You must make a DOS boot diskette using the command FORMAT A:/S/Qin a DOS window under Windows 95 or 98 or DOS. Copy the TestGENI.exe and TestGENI.hlp files to the boot diskette and use it to reboot the NT/2000/XP computer.
TestGENI operates like a BIOS setup program using Up/Down arrows to select lines and Left/Right arrows to change values. You can press the F1 help key to display help text on any line. The four TestGENI screens are:

1. Select type of PCIM card and set the single DIP switch for ELB921/922 cards. Reads EEPROM data.
2. Set I/O port, memory and other info for GENI card. Shows switched for ELB906 or writes EEPROM. Shows LEDS and heartbeat
3. If network is connected, shows status of all Genius devices on network with model type, data lengths and values
4. If PLC bus controllers are connected, perform read datagrams as fast as possible.

Press the [ESC] key to exit each screen. Once you have turned on all PCIM cards and accessed PLC and I/O data, setup is complete. If you used a diskette, remove it and reboot your computer. Start your application software and enter the I/O port and memory address you defined on the second screen in TestGENI. Note: CIMPLICITY HMI and PC Control Genius drivers can setup the EEPROM data directly, but you can still use TestGENI for checkout.

Customer Questions and Answers

• Question:  What is an IC660ELB922?  Answer:  The IC660ELB922 is an ISA Interface Card for the Genius LAN interface. 
• Question:   How many Genius LANS does the card support?   Answer:  The card supports two, independent Genius LANS up to 7,500 feet each.
• Question:   Is IC660ELB922 compatible with a Hand Held Monitor?   Answer:  Yes, this card is fully compatible with a Hand Held Monitor.
• Question:   Is IC660ELB922 compatible with a Bus Controller?   Answer:  Yes, this card may be used with any GE Fanuc Genius bus controller.
• Question:   How many input and output references will the card use?   Answer:  The card will use 8,000 input and 8,000 output references. 
• Question:   What happens if the card is configured as inputs-only?   Answer:  If the configuration of the card is as inputs-only, then it will only read Genius block information.
• Question:   What happens if the card is configured as outputs-only?   Answer:  If the configuration of the card is as outputs-only, then it will only write to Genius block outputs.  
• Question:   What is my next step if my IC660ELB922 has failed?   Answer:  Your product may need repair. 

For more information on the IC660ELB922 ISA Interface Card of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.

The final letter in the part number (ex. IC660ELB922K) indicates the revision. Revision K or later use the newer style electronic housing and therefore needs the newer style plastic door and may indicate some compatibility issues with the terminal strip.