1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC660BBS103CA

★★★★★Rated 4.6/5 Based on 22 ratings.

Rate your purchase of the IC660BBS103

SKU 2175110  UPC 0622527713067

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

The "CA" Revision is for the PDF Supply Conformal Coating Service. PDF Supply warranty will apply. A $150 service charge will be added at checkout.

Product Description

The IC660BBS103 is an eight circuit I/O isolated block by GE Fanuc. The block has a rated voltage of 115 VAC or 125 VDC with an input voltage range of between 93 VAC and 132 VAC. Output voltage range varies from 105 to 132 VDC with a load current of two Amps for every output point.

The IC660BBS103 block’s isolation can withstand a voltage of 250 VAC or VDC between two groups or between a group and a ground. It has a transient rating of 2000V for every 10 seconds. The block can be powered differently from the circuits with power being either AC or DC. The block’s control power can be tapped from the voltages of input/output devices which are wired to the terminals. There is electronic fusing for every circuit used for output. The circuit shuts down immediately after five microseconds in the event of a short circuit. The circuit can thereafter be restarted using a handheld monitor or a CPU. Some of the diagnostic checks include detection of sudden shutdowns, voltage overload, overheating, and detection of power loss to the circuits.

During block mounting, it is advisable to mount the block in a protective enclosure, clean and free from contaminants. It can be mounted facing up or down. It is important to leave two inches of space between blocks for ample ventilation. During field wiring, all terminals will accept 1 AWG #12 wire or 2 AWG #14 wires. The minimum wire size recommended is AWG #22. Ring terminals of up to 0.27 inches can be accommodated by the block. The recommended torque for the terminal screws is 0.678 N/M. Operating temperature for IC660BBS103 ranges from 0-60o C with storage temperature being -40o C to 80o C.

Technical Specifications

Rated Voltage: 115 VAC / 125 VDC
# of Points: 8
Input Voltage Range: 93 - 132 VAC
Output Voltage Range:   105 - 132 VDC
Load Current per Point:  2.0 Amps
Points per Common: Four groups of 2

 

CA - Conformal Coated IC660BBS103CA
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Configuration, Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring, 

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.