GE / IP FANUC Series 90/30 In Stock
IC660BBA025
SKU 2172162 UPC 0799705794054
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC660BBA025 IC660BBA025AIC660BBA025BIC660BBA025CIC660BBA025-CAIC660BBA025DIC660BBA025EIC660BBA025FIC660BBA025HIC660BBA025KIC660BBA025LIC660BBA025MIC660BBA025NIC660BBA025-N1IC660BBA025-RR
Common misspellings:
- 1C660BBA025
- IC66oBBA025
- IC6608BA025
- IC660B8A025
- IC660BBAo25
- IC660BBA025
Product Description
The GE Intelligent Platforms/ GE Fanuc GE-IP Genius I/O IC660BBA025 is a block 24/48Vdc Analog Current Source with six outputs. This block features six 4 to 20 mA analog output circuits with no calibration required for operation. Software configurable, this block has advanced diagnostics and a dedicated bus switching module control. Outputs 5 and 6 can be used as voltage applications if needed.
The blocks provide power to all circuits, and no separate power is required for 4-20mA signals. Each output provides power and control of a 4 to 20mA current loop. IC660BBA025 is a block that has a dedicated digital output that can be used to drive a Bus Switching Module. Handheld monitor model IC66*HHM501G (version 4.0) or later is required for configuration.
When installing the GE Fanuc GE-IP Genius I/O IC660BBA025 know they are considered open equipment and must be installed with a protective enclosure in an area that is clean and free of airborne contaminants. Output channels use a dual 12-bit digital to analog converter and can independently control currents from 0mA to 24mA. The block’s advanced diagnostics provide messages. Fault messages can be cleared from the handheld monitor or CPU.
To configure the block, first use a handheld monitor and enter the device number (serial bus address). Then enter the reference number if required. The blocks configured scaling determines the corresponding output of the signal value. As an added precaution, if the block is configured offline, then it must be properly grounded and have a 75 Ohm resistor installed across Serial 1 and 2 terminals.
Technical Specifications
| Rated Voltage: | 24/48 VDC |
| # of Points: | 6 |
| Output Range: | 4 mA to 20 mA, 0 mA to 24 mA |
| Resolution: | 6 micro Amp |
| Operating Voltage: | 18 - 56 VDC |
| Points per Common: | One group of 6 |
Technical Information
Specifications
|
Block Type: CatalogNumbers: 115 VAC / 125VDCCurrent-source Analog Output block TerminalAssemblyOnly ElectronicsAssemblyOnly 24 / 48VDCCurrent-source Analog Output block TerminalAssemblyOnly ElectronicsAssemblyOnly |
6 Current–source Outputs IC660BBA105 IC660TBA105 IC660EBA105 IC660BBA025 IC666TBA025 IC666EBA025 |
|
Size, Height x Width x Depth: Weight: LED’s (I/O Block): BSMControl: |
8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm) 4 lbs. (1.8 kg) UnitOK,I / OEnabled Switchesone 24 / 48 VDC BSM (IC660BSM021) |
|
Block to Block Isolation: |
1500 V for one minute |
|
HeatDissipation: |
12 Wattsmaximum |
|
115VAC blockpower: Powersupplyvoltage Maximumcurrent Frequency / ripple Power supply dropout time |
93–132 VAC 250mA 47–63 Hz 1 cycle |
|
125VDCblockpower: Powersupplyvoltage Maximumcurrent Frequency / ripple Power supply dropout time |
105–145 VDC 140mA 10% max. ripple 10mSmin. |
|
24/48 VDCblockpower: Powersupplyvoltage Maximumcurrent Ripple Power supply dropout time |
18–56 VDC 600mA 10% max. 10mSmin. |
|
OutputSignalCharacteristics: Accuracy at 25 C Resolution Updatefrequency Range Overrangecapacity Diagnostics Load
Thermal drift (from 25 C) |
0.15% of full–scale reading 6ïA 25mS < 4mA to 20mA 0mAto24mA Underrange, Overrange, Feedback error 0 ohms to 850 ohms (currentapplication) 0 to 10mA: 0 to 5–volt application 0 to 10mA: 0 to 20–volt (maximum) voltage application 35 PPM per C typical |
|
Environmental: Operating Temperature Storage Temperature Humidity Vibration |
0C to +60C (+32F to +140F) –40C to +100C (–40F to +212F) 5% to 95% (non–condensing) 5 – 10 Hz 0.2” (5.08mm) displacement, 10–200 Hz at 1G |
Troubleshooting
Troubleshooting IC660BBA025
Troubleshooting information is available on IC660BBA025's website page; it also includes a datasheet, a user manual, and a wiring diagram.
Repair your IC660BBA025
PDF Supply can repair your IC660BBA025 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC660BBA025? Answer: The IC660BBA025 is a 24/48 VDC Current-Source Analog Output Block from the GE Fanuc Genius I/O Series. IC660BBA025 provides power to all circuits. This block has 6 output circuits for devices that accept 4-20mA signals.
- Question: What is the difference between IC660BBA025 and IC660BBA105? Answer: The only difference between these blocks is their power supply.
- Question: What features are included with IC660BBA025? Answer:
- 6 4-20mA analog output circuits
- No calibration is required for operation.
- Configurable software
- Diagnostics that are advanced.
- Dedicated Bus Switching module control
- Question: Is any separate power required for 4-20mA signals? Answer: No, no separate power is required.
- Question: What does each output provide? Answer: Each one provides power and control of a 4-20mA current loop.
- Question: What is special about this power? Answer: It is isolated from the rest of the block.
- Question: What features of this block can be configured? Answer:
- Output Hold Last State or default
- Circuit scaling to engineering the unit's values
- Output feedback checking and feedback time
- CPU Redundancy
- Question: What should I do if my IC660BBA025 has failed? Answer: Your IC660BBA025 may need repair.
For more information on the IC660BBA025 Current-Source Analog Output Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.
The final letter in the part number (ex. IC660BBA025K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.
Common related search terms: ConfigurationDatasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
