1-800-360-6802
[email protected]

GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

1-800-360-6802

Mon-Fri 8AM-5PM EST

[email protected]

IC660BBA020CA

★★★★★Rated 4.8/5 Based on 14 ratings.

Rate your purchase of the IC660BBA020

SKU 2172241  UPC 0799705802971

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to indicate any affiliation with or authorization by any rights holder.

The "CA" Revision is for the PDF Supply Conformal Coating Service. PDF Supply warranty will apply. A $150 service charge will be added at checkout.

Product Description

The IC660BBA020 is a voltage/current analog block in the GE Fanuc Genius I/O series. It has four input and two output circuits. Two types of analog blocks are available with a power supply of 115 VAC and 24/48 VDC. IC660BBA020 supports five analog ranges: 0-10 volts DC; -10 volts DC to +10 volts DC; -5 volts DC to +5 volts DC; 0-5 volts DC; and 4-20 mA/1-5 volts DC. The internal power supply of this block can drive a current load of 300 Ohms.  Configurable block features include independent scaling; fault reports which can be enabled or disabled depending on input/output; selectable input filter time up to 1024ms; powerup default values for each output; and Low/High Alarm detection, among others.

 

IC660BBA020 is compatible with any handheld monitor IC66*HHM500, though HHM501 requires a change in configuration. The serial bus uses terminals 1 to 4 with AWG wires. Field devices use terminal 5 to 32 with AWG wires. Terminals 6 (DC+) and 7 (DC-) connect the power source to the 24/48 VDC. H and N terminals connect  the 115 VAC block with the 250V, 1/8Amp slow blow fuse. Terminals 5, 12, 28, and 20 are for ground. Three terminals named common are for a source. The user can connect input voltage device between V+ and IN and V- and RTN terminal in series. The user can connect output voltage device to terminals COM and VOUT. JMP terminal is for jumper connection. Terminals I+ and I- are for the current mode.  The first four input circuits convert incoming current or voltage signal to digital count with optional scaling. Circuit numbers 5 and 6 give output scaled digital count from CPU. I/O Enabled and Unit OK LEDs indicate the operating status of the block. The diagnostics system indicates fault messages.


Technical Specifications

Rated Voltage: 24/48 VDC 
# of Points: 4 Inputs / 2 Outputs
Input Range: 0-10 VDC, -10 to +10 VDC, -5 to +5 VDC, 0-5 VDC, 4-20 mA 
Output Range: 0-10 VDC, -10 to +10 VDC, -5 to +5 VDC, 0-5 VDC, 4-20 mA
Operating Voltage: 18 - 56 VDC
Points per Common:   One group of 4 Inputs and one group of 2 Outputs

 

CA - Conformal Coated IC660BBA020CA
ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

Common related search terms: Datasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring, 

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.