GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

Mon-Fri 8AM-5PM EST

IC600YB910

Rated 4.5/5 Based on 6 ratings.

Rate your purchase of the IC600YB910
IC600YB910 In Stock! 115Vac Isolated Output Module (6 points) IC600Y IC600YB PDFsupply also repairs

SKU 2177421  UPC 0707180931062

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

New Surplus

$203

8 In Stock

✓  3 Year PDF Supply Warranty

*What is New Surplus?

Ships .

Surplus New

$176

Save $27

4 In Stock

✓  3 Year PDF Supply Warranty

*What is Surplus New?

Ships .

Reman

$160

Save $43

106 In Stock

✓  2 Year PDF Supply Warranty

*What is Remanufactured?

Ships .

115Vac Isolated Output Module (6 points)Series Six Module Without Face Plate IC600Y IC600YB

Technical Information

The GE Fanuc Series 6 Programmable Logic Controller (PLC) system is able to control external loads by using 115 Volts AC voltage and with an additional module known as the GE Fanuc IC600YB910 115 Volts AC isolated output module. This solid-state module enables the programmable logic controller to command 6 independent, 115 Volts AC rated outputs at a time with a constant current rating of 3 Amps and a maximum inrush current of approximately 20 Amps for 33 milliseconds. Each of these 6 independent outputs are provided with independent source and output connections. The operating temperature range of the module is between 0 and 60 degrees Celsius, and for higher or lower temperature extremes, it is necessary to place the GE Fanuc IC600YB910 115 Volts AC isolated output module inside a protective enclosure with climate control.

 

Installing the GE Fanuc IC600YB910 115 Volts AC isolated output module in an I/O rack or GE Series 6 Model 60 CPU rack is easy because it simply involves insertion into any available slot. The manufacturer recommends using the extraction tool that is included with the device anytime the module needs to be manipulated or adjusted. It is also important to fasten the faceplate of the module into the rack by using the 2 screws located at the top and the bottom of the unit. The GE Fanuc IC600YB910 115 Volts AC isolated output module is equipped with a DIP switch to configure the action of each of the 6 independent outputs. Hot swap operations are not possible with this module because the board may be damaged by improper handling. Only properly trained technicians should be allowed to perform maintenance operations on this device.

ST. LOUIS, Feb. 1, 2019 – Emerson today announced it has completed the purchase of Intelligent Platforms from General Electric.

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.