GE / IP FANUC Series 90/30 In Stock
Home » Allen Bradley » MicroLogix 1200 » You are here: 1762-L24AWAR
1762-L24AWAR
Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the 1762-L24AWAR 1762-L24AWAR//A1762-L24AWAR//B1762-L24AWAR//C
Common misspellings:
- l762-L24AWAR
- 1762-124AWAR
- 1762-L2AAWAR
- 1762L24AWAR
Technical Specifications for 1762-L24AWAR
| Manufacturer: | Rockwell Automation / Allen-Bradley |
|---|---|
| Brand: | Allen-Bradley |
| Product Type: | MicroLogix 1200 Controller |
| Part Number: | 1762-L24AWAR |
| Number of I/O: | 24 |
| Number of Inputs: | 14 |
| Input Operating Range: | 79-132VAC |
| Number of outputs: | 10 (Relay) |
| Relay Output operating range: | 5 - 125V DC / 5 - 264V AC |
| Output Signal Delay: | 10 ms |
| Communication ports: | One (1) RS232 / RS485 combo port; One (1) Programmer port |
| Communication protocol: | DH485, DF1 Full-Duplex, DF1 Half Duplex, DF1 Radio Modem, MODBUS Master / Slave and ASCII protocols. |
| Power supply: | 100-240VAC |
| Operating Frequency: | 47-63 Hz |
| Accessory components: | 1762-MM1; 1762-RTC; 1762-MM1RTC |
| Programming Software: | RSLogix 500 |
About 1762-L24AWAR
The 1762-L24AWAR is a Programmable Logic Controller (PLC) that belongs to the MicroLogix 1200 product family. This compact electronic component is manufactured by Allen-Bradley, ideal for implementing automation of micro and small processes. The 1762-L24AWAR features an integrated Fourteen (14) 120VAC discrete inputs and Ten (10) Relay output channels. The inputs channels have a minimum ON state voltage of 79VAC while the maximum OFF state voltage is 132VAC. The relay output channels may be operated for Voltage ranges of 5-125VDC or 120-240VAC. Both these embedded I/Os are used for integrating and controlling discrete devices that operate in binary or Two-position actuations, commonly known as ON/OFF modes. Compatible field devices for input channels are switches, sensors, auxiliary contacts while output devices may be used to energize electrical loads such as magnetic contactors, relays coils, pilot lamps, buzzers, hors, siren, solenoid, soft starters and other compatible devices. It also has Two (2) communication ports, one being an RS232/RS485 combo port which can be used for downloading and uploading PLC programs, established communication between computer-based control systems such as Human Machine Interface (HMI), Supervisory Control and Data Acquisition (SCADA), Distributed Control Systems (DCS), enterprise tools such as databases, ERMs, gateways, protocol converters and other compatible partner devices. The secondary communication port is a dedicated programmer port that supports DF1 Full Duplex protocol only. This is mainly used for downloading and uploading PLC programs as this port cannot initiate messages. This port has a fixed communication parameter set. Both the physical communication terminal are 8-pin mini DIN terminals, compatible with communication cables such as 1761-CBL-PM02 series C or later,1761-CBL-HM02 series C or later. 1761-CBL-AM00 series C or later, 761-CBL-AP00 series C or later 1761-CBL-PH02 series A or later, 1761-CBL-AH02 series A or later, 2707-NC8 series A or later, 2707-NC9 series B or later, 2707-NC10 series B or later and 2707-NC11 series B or later. RS232 communication from the primary communication port or Channel 0 supports DH485, DF1 Full-Duplex, DF1 Half Duplex, DF1 Radio Modem, MODBUS Master / Slave and ASCII protocols. The RS485 supports daisy chain topology primary MODBUS RTU communication. This controller is powered up with a voltage range of 79-265 VAC along an operating frequency of 47-63 Hz. It can withstand an inrush current of 25A for 8 ms when operated at 120VAC input and 40A for 4 ms for 240VAC. The controllerÕs power supply usage is 68VA. The controllerÕs power supply output is 400 mA at 5VDC and 350 mA at 350 mA.F.A.Q for 1762-L24AWAR
| Q: 1. What is the main difference of the 1762-L24AWA with 1762-L24AWAR? | A: The main difference is the 1762-L24AWAR has secondary communication port which is a programmer port dedicated for DF1 Full duplex protocol. |
|---|---|
| Q: 2. Can I use 1769 Compact I/O modules instead of 1762 MicroLogix I/O expansion modules? | A: No, only the 1762 MicroLogix I/O modules can be used with this controller. Compact I/O are used for MicroLogix 1500. |
| Q: 3. How many expansion modules are supported by this controller? | A: This module supports up to Six (6) 1762 expansion modules may be used with this module. |
PDFsupply Tech
The 1762-L24AWAR is a MicroLogix 1200 controller which has very similar features with the 1762-L24AWA. It has the same I/O count of 24 I/O. The main difference of this controller is the secondary programmer port which is dedicated for programming functions only. This allows the controller to be programmed without the need of removing the communication interface attached to the primary channel 0 port. This may contribute to lessen process or machine downtime.
