GE / IP FANUC Series 90/30 In Stock
Home » Allen Bradley » MicroLogix 1200 » You are here: 1762-IQ32T
1762-IQ32T
Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the 1762-IQ32T 1762-IQ32T//A
Common misspellings:
- l762-IQ32T
- 1762-1Q32T
- 1762-lQ32T
- 1762IQ32T
Technical Specifications for 1762-IQ32T
| Manufacturer: | Rockwell Automation |
|---|---|
| Brand: | Allen-Bradley |
| Product Description: | MicroLogix Expansion I/O Module |
| Product Type: | Discrete Input Module |
| Part Number: | 1762-IQ32T |
| No. of Inputs: | 32 |
| No. of Groups: | 4 groups (8 inputs each) |
| Voltage Category: | 24V DC sink/source |
| Input Voltage Range: | 10 - 30V DC or 10 - 26.4V DC |
| Compatible Controllers: | MicroLogix 1100, 1200 and 1400 |
| Off-state Voltage: | 5V DC |
| On-state Voltage: | 10V DC |
| Input delay, On: | 8 ms |
| Input Delay, Off: | 8 ms |
| Bus current draw, max: | 170 mA @ 5V DC; 0 mA @ 24VDC |
| Dimensions, HxWxD: | 90 x 40.4 x 87 mm (3.54 x 1.59 x 3.43 in.) |
About 1762-IQ32T
The 1762-IQ32T is an expansion module compatible for use with MicroLogix 1100, 1200 and 1400 Controller. This module is a High-density input module with Thirty-Two (32) channels supporting sinking and sourcing wiring configuration with each channel operating at voltage range of 10-26.4V DC or 10-30V DC. This module had Four (4) input groups, with Eight (8) channels each group. This enables each group to be independently wired in any of the 2 supported configurations and provide isolation. This module is typically used to integrate switching devices, supporting 2 positions only, ON and OFF. Signaling devices such as switches, sensors, auxiliary contacts, and other electrical and electronic components are compatible with this module. Input group 1 is composed of channels 0, 1, ,2 ,3 ,4 ,5 ,6 ,7; Group 2 is made of channels 8, 9, 10, 11, 12, 13, 14, 15; Groups 3 has channels 16, 17, 18, 19, 20, 21, 22 and 23 and input group 4 is composed of channels 24, 25, 26, 27, 28, 29, 30 and 31. This module uses a pre-assembles connector with catalog number 1746-N3. This wire is a Forty (40) pin female connector and crimp type pins. One end of the connector is a keyed female that aligns to the moduleÕs Keyed male MIL-C-083503 connector. The other end of the cable are flying leads that may be may be terminated to terminal blocks and Printed Circuit Board (PCB). Similar to other 1762 Expansion I/O modules, the 1762-IQ32T has a rackless design with integrated that connects to other modules or the base MicroLogix module using a flat ribbon cable. MicroLogix 1100 supports installation of up to Four (4) 1762 Expansion modules, Six (6) with MicroLogix 1200 and Seven (7) for MicroLogix 1400. This quantity of supported modules allows combination of different module a single type of module only. This arrangement depends mainly on the system requirement. This module requires I/O configuration definition. The corresponding data file start with Slot 1 as Slot 0 is reserved for the embedded channels of any MicroLogix Controller. The 1762-IQ32T input channelÕs ON signal delay is 8.0 ms while OFF signal delay is 8.0 ms while the minimum ON state voltage is 10VDC and maximum OFF state voltage is 5VDC. The module is energized through the backplane with a current draw of 170 mA @ 5V DC and 0 mA @ 24VDC. Use wire size ranging from 22, 24, 26 AWG solid or stranded copper wire rated @ 90¡C (194 ¡F). The moduleÕs dimension is 90 x 40.4 x 87 mm (3.54 x 1.59 x 3.43 in.).F.A.Q for 1762-IQ32T
| Q: 1. Does the 1762-IQ32T support sourcing configuration? | A: Yes, the Four (4) input groups of this module individually support sinking and sourcing configuration. |
|---|---|
| Q: 2. Does this cable require a specialty cable for wiring input signals? | A: Yes, this module uses a pre-assembled cable with catalog number 1746-NC3. This may also be fabricated following the pinout configuration. |
| Q: 3. Does this module support 120/240 VAC wiring? | A: If directly wired, No. If used with an interposing circuit, this module may be used. |
PDFsupply Tech
The 1762-IQ32T is a high-density Discrete input module with 32 channels. This module has a greater input channels quantity compared to the 1762-IQ16 which means it support up to 32 switching devices. It also uses a prefabricated cable which may also be custom build.
