GE / IP FANUC Series 90/30 In Stock

World's Largest Warehouse

of GE 90-30, Genius, and RX7i

Mon-Fri 8AM-5PM EST

HE693RTD660

Rated 4.6/5 Based on 13 ratings.

Rate your purchase of the HE693RTD660
Horner Electric | Horner Electric | HE693RTD660 | Image

SKU 2176318  UPC 0339314650367

All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.

PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.

The HE693RTD660 allows RTD temperature sensors to be connected to the PLC directly without external signal processing such as transducers, transmitters, etc. All analog and digital processing of the RTD signal is performed on the module. These backplane-isolated (or bus-isolated) modules have programmable resolutions in increments of 0.05oC, 0.05oF,0.1oC, 0.1oF, 0.5oC, 0.5oF. The module features six channels whose temperature values are reported to the 6 %AI input registers. There are 6 %I alarm bits and one setpoint alarm for each channel. Alarm setpoints are configured for each channel using 6 %AQ registers. All modules feature support for the following RTD types: PT-100 (platinum, 100W at 0°C), Ni-120 (nickel, 120W at 0°C), Cu-10 (Copper,10W at 25°C), Pt-1000 (platinum, 1000W at 0°C), and TD5R Silicon (Microswitch).

Technical Specifications


Power Consumption (Typical) 200mA @ 5VDC
Number of Channels 6
Resolution 0.05°C, 0.05°F, 0.1°C,0.1°F, 0.5°C, or 0.5°F
Accuracy +/- 0.3°C
RTD Short Indefinite without damage
I/O Points Required 6%AI, 6% AQ, 16%I
Input Impedance >1000 Megohms
Input Transient Protection Suppression Diode
A/D Conversion Type 18 bit, Integrating
Update Time 50 channels/sec. (660)12.5 Channels/sec. (665/666)
Average RTD Current 330 microamps
Channel to Channel Tracking 0.1°C
Operating Temperature 0 to 60°C (32 to 140°F)
Relative Humidity 5% to 95% non-condensing
Channel-to-Bus Isolation 1500V AC
Channel-to-Channel Isolation 5V AC

Technical Information

Power Consumption (Typical) 200mA @ 5VDC
Number of Channels 6
Resolution 0.05°C, 0.05°F, 0.1°C,0.1°F, 0.5°C, or 0.5°F
Accuracy +/- 0.3°C
RTD Short Indefinite without damage
I/O Points Required 6%AI, 6% AQ, 16%I
Input Impedance >1000 Megohms
Input Transient Protection Suppression Diode
A/D Conversion Type 18 bit, Integrating
Update Time 50 channels/sec. (660)12.5 Channels/sec. (665/666)
Average RTD Current 330 microamps
Channel to Channel Tracking 0.1°C
Operating Temperature 0 to 60°C (32 to 140°F)
Relative Humidity 5% to 95% non-condensing
Channel-to-Bus Isolation 1500V AC
Channel-to-Channel Isolation 5V AC
  • Question: What is the HE693RTD660? Answer: The HE693RTD660 allows RTD temperature sensors to be connected to the PLC directly without external signal processing such as transducers, transmitters, etc. All analog and digital processing of the RTD signal is performed on the module. These backplane-isolated (or bus-isolated) modules have programmable resolutions in increments of 0.05oC, 0.05oF,0.1oC, 0.1oF, 0.5oC, 0.5oF. The module features six channels whose temperature values are reported to the 6 %AI input registers. There are 6 %I alarm bits and one setpoint alarm for each channel. Alarm setpoints are configured for each channel using 6 %AQ registers. All modules feature support for the following RTD types: PT-100 (platinum, 100W at 0°C), Ni-120 (nickel, 120W at 0°C), Cu-10 (Copper,10W at 25°C), Pt-1000 (platinum, 1000W at 0°C), and TD5R Silicon (Microswitch).
  • Question: What type of power consumption does HE693RTD660 use? Answer: The main power source for the HE693RTD660 uses 200mA @ 5VDC.
  • Question: Where should the components be mounted? Answer: All components must be mounted in a metal enclosure or the equivalent.
  • Question: Do the cables and analog signals should be shielded? Answer: All cables and analog signals must use shielded cable with a minimum of overall foil.
  • Question: Can I change the number of channels or the voltage on this device? Answer: Yes, you can. This is a 6 channel unit.

 

PDF Supply sells used surplus products. PDF Supply is not an authorized distributor, affiliate, or representative for the brands we carry. Products sold by PDF Supply come with PDF Supply’s 1-year, 2-year, or 3-year warranty and do not come with the original manufacturer’s warranty. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. This website is not sanctioned or approved by any manufacturer or tradename listed.

Rockwell Disclaimer: The product is used surplus. PDF Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because PDF Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, PDF Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. PDF Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. PDF Supply also makes no representations as to your right to install any such firmware on the product. PDF Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.