GE / IP FANUC Series 90/30 In Stock
IC694ALG391
RX3i ALG391 Analog
SKU 2178264 UPC 0799705802407
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC694ALG391 IC694ALG391AIC694ALG391BIC694ALG391-LT
Common misspellings:
- 1C694ALG391
- IC69AALG391
- IC694A1G391
- IC694ALG39l
- IC694ALG391
Technical Specifications for IC694ALG391
| Manufacturer | GE Fanuc |
|---|---|
| Series | RX3i PACSystems |
| Part Number | IC694ALG391 |
| Product Type | Analog Output Module |
| Outputs | 2 |
| Data Conversion Rate | 12 Bits of Binary Data to Output Signals |
| Output Signal Range | 0-20 mA, 4-20 mA |
| Series 90-30 Expansion Backplane | Supported |
| RX3i Serial Expansion Backplane | Supported |
| LED Indicator | 1 "Module OK" LED |
Product Description
The GE Fanuc IC694ALG391 is a two channel analog current output module. Each of the two channels is capable of converting 12 bits of binary data for field devices. Additionally, each output can be set up using a jumper to construct varying signals, 0 to 20 mA or 4 to 20 mA. Each output can be set as a less exact voltage source, and the range is made with a jumper or resistor on the terminals as decided by the user.
Though an external source of isolated +24 VDC is vital for power for the module, it can be linked via the TB1 connector on the backside or directly to the terminal block. Both are effective methods for this model. However, if the user needs to preserve hold last state operation during a loss of backplane power, then an outside source is needed. An update rate of 5 milliseconds on both channels is application dependent but available.
When installing the GE Fanuc IC694ALG391, a good grade of twisted, shielded instrumentation cable should be used to lessen noise and capacitive loading. Each channel’s range is set with jumpers on the module terminals, and for voltage operation, a 250 Ohm resistor can be used in place of a voltage jumper if desired. Note: If the output default jumper is installed on module terminals 11 and 13, then both outputs will default, using the low end of their range. If the output jumper is not installed, both outputs will hold the last valid output value that was acknowledged. However, this route requires an external +24 VDC power supply.
Technical Specifications
| No. of channels: | 2 |
| Voltage Range: | 1-5 V, 0-5 V |
| Current Range: | 0-20 mA, 4-20 mA |
| Update Rate: | 5 msec |
| Output Load: | 5 mA max |
| Power Consumption: | 30 mA @ +5VDC, 120 mA @ +24VDC Isolated |
The GE Fanuc IC694ALG391 RX3i PACSystems analog output module is capable of handling various loads at different DC voltage levels. It has a capacity for maximum loads of 30 milliamps or 0.15 Watts at 5 Volts DC, and it can handle loads of up to 5.16 Watts or 215 milliamps at an isolated voltage of 24 Volts DC. The 2 output channels of the IC694ALG391 analog output module convert the digital data or 12 bits of binary data into analog output signals for various field devices that can be connected to it. The operators have the ability to configure output modules like this one with jumpers and produce converted output signals in a current range of 4 to 20 milliamps or 0 to 20 milliamps. When the GE Fanuc IC694ALG391 output module is operating normally, it has a green “Module OK” LED indicator that lights up.
Technical Information
Specifications:
|
Output Current Range |
4 to 20 mA and 0 to 20 mA |
|
Output Voltage Range |
1 to 5 volts and 0 to 5 volts |
|
Calibration |
Factory calibrated to 4 µA per count |
|
External Supply Voltage Range |
20 VDC to 30 VDC. Depends on the current load |
|
|
and the ambient temperature as shown below. |
|
External Supply Voltage Ripple |
10% |
|
Update Rate |
5 milliseconds (approximate, both channels) |
|
|
Application dependent. |
|
Resolution: |
|
|
4 to 20mA |
4 µA (1 LSB = 4 µA) |
|
0 to 20mA |
5 µA (1 LSB = 5 µA) |
|
1 to 5V |
1 mV (1 LSB = 1 mV) |
|
0 to 5V |
1.25 mV (1 LSB = 1.25 mV) |
|
Absolute Accuracy: * |
|
|
4 to 20mA |
+/-8 µA at 25°C (77°F) |
|
0 to 20mA |
+/-10 µA at 25°C (77°F) |
|
1 to 5V |
+/-50 mV at 25°C (77°F) |
|
0 to 5V |
+/-50 mV at 25°C (77°F) |
|
Maximum Compliance Voltage |
25 VDC |
|
User Load (current mode) |
0 to 850 Ohms |
|
Output Load Capacitance (current mode) |
2000 pF |
|
Output Load Inductance (current mode) |
1 H |
|
Maximum Output Loading (voltage mode) |
5 mA (2 K Ohms minimum resistance) |
|
|
(2000 pF maximum capacitance) |
|
Isolation, Field to Backplane (optical) and to |
250 VAC continuous; 1500 VAC for 1 minute |
|
frame ground |
|
|
Internal Power Consumption |
30 mA from +5 VDC supply |
|
|
215 mA from Isolated +24 VDC supply |
Troubleshooting
Troubleshooting IC694ALG391
Troubleshooting information is available on IC694ALG391's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC694ALG391
PDF Supply can repair your IC694ALG391 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC694ALG391? Answer: The IC694ALG391 is a 2 Channel, Current, Analog Output module from the GE Fanuc RX3i Series.
- Question: What does IC694ALG391 have and what is it capable of doing? Answer: IC694ALG391 has 2 output channels and each of those channels is capable of converting 12 bits of binary (digital) data to an analog output signal for field devices.
- Question: What does each output of IC694ALG391 produce? Answer: Each output can be set, using a jumper on the module, to produce output signals from 0 to 20 mA or 4 to 20 mA.
- Question: How else can each output be set up? Answer: Each output may also be set up as a less accurate voltage source.
- Question: How is the selection of current or voltage output made? Answer: It is made by a jumper or a resistor on the module terminals.
- Question: How are the module outputs set up? Answer: They can be set up to either Default to 0/4 mA or Hold-Last-State if the CPU goes to the Stop mode or Reset.
- Question: How is the selection of the output Default State made? Answer: It is made by a jumper on the module's terminal board.
- Question: What should I do if my IC694ALG391 is not working properly? Answer: Your IC694ALG391 may need repair.
For more information on the IC694ALG391 2 Channel, Current, Analog Output Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.
Common related search terms: BatteryBuy, Configuration, Datasheet, Dimension, Emerson, Fanuc, Firmware, GE, GE-Fanuc, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
