GE / IP FANUC Series 90/30 In Stock
IC694ALG222
RX3i ALG222 Analog
SKU 2175133 UPC 0799705802421
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC694ALG222 IC694ALG222-AAIC694ALG222-BAIC694ALG222-CAIC694ALG222-DBIC694ALG222-LT
Common misspellings:
- 1C694ALG222
- IC69AALG222
- IC694A1G222
- IC694ALG222
Technical Specifications for IC694ALG222
| Manufacturer | GE Fanuc |
|---|---|
| Series | RX3i PACSystems |
| Part Number | IC694ALG222 |
| Product Type | Analog Input Module |
| Number of Channels | 1 to 16 selectable (single-ended), 1 to 8 selectable (differential) |
| Input Current Ranges | 0 Volts to 10 Volts (unipolar), -10 Volts to +10 Volts (bipolar) |
| Update Rate | 6 milliseconds (all 16 single-ended channels), 3 milliseconds (all 8 differential channels) |
| Linearity | Less than 1 LSB |
| Isolation Voltage | 250 Volts AC (continuous), 1500 Volts AC for 1 minute |
| Cross-Channel Rejection | Less than 80 decibels from DC to 1 kilohertz |
Product Description
IC694ALG222 is a 16-Channel Analog Voltage Input Module manufactured by GE Fanuc that provides 16 single-ended (or eight) differential input channels. Each channel can be configured using configuration software for either input range options: 0 to 10 V (unipolar) or default -10 to +10 V (bipolar). High/low alarm limits can also be configured for unipolar or bipolar ranges. The IC694ALG222 can be installed in any I/O slot of an RX3i system.
Location of the IC694ALG222 module is important when identifying the appropriate power source. If the IC694ALG222 module is located in a Universal Backplane, an external source of Isolated +24 VDC is needed. The external source should be connected using the TB1 connector on the left side of the backplane. If the module is in an Expansion Backplane, the power supply provides the Isolated +24 VDC.
Status information is indicated by the MODULE OK LED on power-up. ON means the status is OK, and the module is configured. OFF means there is no backplane power, or the software is not running (in other words, the watchdog timer has timed out. If the LED displays continuous rapid flashing, this suggests that configuration data is not being received from the CPU. Slow flashing followed by OFF indicates failed power-up diagnostics or a code execution error. The Module P/S LED confirms that the module’s +5 VDC supply meets the minimum designated level.
Technical Specifications
| No. of channels: | 16 single-ended or 8 differential |
| Voltage Range: | -10 to +10 V, 0 to 10 V |
| Calibration: | Factory calibrated |
| Update Rate: | 6 msec(all 16), 3 msec(all 8) |
| Input Filter Response: | 41 Hz, 82 Hz |
| Power Consumption: | 112 mA @ +5VDC, 41 mA @ +24VDC Isolated |
The IC694ALG222 input module has an internal power consumption rating of up to 112 milliamps from the backplane at +5 Volts DC bus voltage. Additionally, the internal power consumption from the isolated +24 Volts DC backplane supply is 41 milliamps (maximum). The IC694ALG222 input module has a linearity of less than 1 LSB and an isolation voltage of 250 Volts AC for continuous operation. The isolation voltage for the 1-minute operation is 1500 Volts AC. The unit has a cross-channel rejection of less than 80 decibels from DC to 1 kilohertz. The unit has an input impedance of less than 500 kiloohms for the single-ended mode and less than 1 megaohm for the differential mode. The IC694ALG222 input module has LED indicators for the module status and it features configurable parameters for the active channels, mode, length, range, alarm, and the reference address for input data. The default operating mode of the IC694ALG222 module is the single-ended mode while the differential mode requires configuration.
Technical Information
Specifications:
|
Number of Channels |
1 to 16 selectable, single-ended 1 to 8 selectable, differential |
|
Input Voltage Ranges |
0 V to +10 V (unipolar) or -10 V to +10 V (bipolar); selectable each channel |
|
Calibration |
Factory calibrated to: 2.5 mV per count on 0 V to +10 V (unipolar) range 5 mV per count on -10 to +10 V (bipolar) range |
|
Update Rate |
Single Ended Input Update Rate: 5 ms Differential Input Update Rate: 2 ms |
|
Resolution at 0V to +10V |
2.5 mV (1 LSB = 2.5 mV) |
|
Resolution at -10V to +10V |
5 mV (1 LSB = 5 mV) |
|
Absolute Accuracy 1,2 |
±0.25% of full scale @ 25°C (77°F) ±0.5% of full scale over specified operating temperature range |
|
Linearity |
< 1 LSB |
|
Isolation, Field to Backplane (optical) and to frame ground |
250 VAC continuous; 1500 VAC for 1 minute |
|
Common Mode Voltage (Differential)3 |
±11 V (bipolar range) |
|
Cross-Channel Rejection |
> 70dB from DC to 1 kHz |
|
Input Impedance |
>500K Ohms (single-ended mode) >1 Megohm (differential mode) |
|
Input Filter Response |
23 Hz (single-ended mode) 57 Hz (differential mode) |
|
Internal Power Consumption |
112 mA (maximum) from the backplane +5 VDC bus 110 mA (maximum) from the backplane isolated +24 VDC supply |
Troubleshooting
Troubleshooting IC694ALG222
Troubleshooting information is available on IC694ALG222's website page; it also includes a datasheet user-manual and a wiring diagram.
Repair your IC694ALG222
PDF Supply can repair your IC694ALG222 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC694ALG222? Answer: The IC694ALG222 is a 16/8 Channel, Voltage, Analog Input module from the GE Fanuc RX3i Series.
- Question: What does IC694ALG222 provide? Answer: This module provides 16 single-ended or 8 differential input channels.
- Question: For what 2 ranges can each channel be configured using the configuration software? Answer:
- 0 to 10 V (unipolar), default
- -10 to +10 V (bipolar)
- Question: Can high and low alarm limits be configured for both ranges? Answer: Yes, they can.
- Question: Into what slot can IC694ALG222 be installed, in an RX3i system? Answer: This module can be installed in any I/O slot of an RX3i system.
- Question: If the module is located in an RX3i Universal Backplane- what then? Answer: Then that means an external source of isolated +24 VDC is required to provide power for the module.
- Question: How must the external source be connected? Answer: The external source must be connected via the TB1 connector on the left side of the backplane.
- Question: If IC694ALG222 is located in an Expansion Backplane- what then? Answer: Then the backplane's power supply provides the isolated +24 VDC for IC694ALG222.
- Question: What do the LEDs on IC694ALG222 indicate? Answer:
- ON: status is OK, module configured
- OFF: no backplane power or software not running (watchdog timer timed out)
- Continuous rapid flashing: configuration data not received from CPU
- Slow flashes, then OFF: failed power-up diagnostics or encountered code execution error
- The Module P/S LED indicates that the module's internally generated +5 VDC supply is above a minimum designated level
- Question: What should I do if my IC694ALG222 is not working properly? Answer: Your IC694ALG222 may need repair.
For more information on the IC694ALG222 16/8 Channel, Voltage, Analog Input Module of the GE Fanuc RX3i Series, please see the Datasheet User-Manual.
Release History
|
Version |
Firmware Release |
Date |
Description |
|
IC694ALG222-DB IC693ALG222-HB |
1.60 |
May 2012 |
Resolves several rarely-occuring issues that were identified in field and factory testing. |
|
IC694ALG222-CA IC693ALG222-GA |
1.10 |
Feb. 2012 |
Hardware revision to correct delayed detection of a disconnected input. |
|
IC694ALG222-BA IC693ALG222-FA |
1.10 |
May 2011 |
Adds ability to perform field upgrades in RX3i targets. Adds display of module serial number, revision and date code in programming software in RX3i targets. |
Common related search terms: BatteryBuy, Configuration, Datasheet, Dimension, Emerson, Fanuc, Firmware, GE, GE-Fanuc, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
