GE / IP FANUC Series 90/30 In Stock
IC660BBD020
SKU 2176220 UPC 0799705793477
All product names, trademarks, brands and logos used on this site are the property of their respective owners. PDF Supply is not an authorized distributor, reseller or representative of the products featured on this website. The depiction, description or sale of products featuring these names, trademarks, brands and logos is for identification purposes only and is not intended to in indicate any affiliation with or authorization by any rights holder.
PDF Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with PDF Supply's 1-year, 2-year, or 3-year warranty.
Other Available Revisions for the IC660BBD020 IC660BBD020AIC660BBD020BIC660BBD020CIC660BBD020-CAIC660BBD020DIC660BBD020EIC660BBD020FIC660BBD020HIC660BBD020KIC660BBD020LIC660BBD020MIC660BBD020NIC660BBD020PIC660BBD020QIC660BBD020RIC660BBD020-RRIC660BBD020SIC660BBD020TIC660BBD020UIC660BBD020VIC660BBD020WIC660BBD020XIC660BBD020YIC660BBD020-Y1
Common misspellings:
- 1C660BBD020
- IC66oBBD020
- IC6608BD020
- IC660B8D020
- IC660BBDo20
- IC660BBD02o
- IC660BBD020
Technical Specifications for IC660BBD020
| Manufacturer | GE Fanuc |
|---|---|
| Series | Genius I/O |
| Part Number | IC660BBD020 |
| Product Type | DC Source I/O Block |
| Compatibility | GE Fanuc Series 90-30 PLCs |
| Supply Voltage | 24 to 48 Volts DC |
| Number of I/O Circuits | 16 |
| Output Current (Steady State) | 2 Amps per circuit |
| Maximum Inrush Current | 10 Amps during 10 milliseconds |
| Environmental Protection Rating | IP 20 |
Product Description
The IC660BBD020 is 24/48 VDC Source I/O, 16 Circuit, 3 Wire Sensor Compatible Block of GE Fanuc series 90-30 PLCs. It is a configurable block that interfaces 3-wire solid state and electromechanical sensors. This block works with 24 or 48 VDC and provides current to output devices only. The IC660BBD020 has 16 discrete circuits. Each of them can be configured as input, tristate input, or output with different parameters and features. It also has advanced diagnostic capabilities. It can detect installation problems or run-time errors. It reports them to the handheld monitor and takes appropriate corrective action. Some of them are short circuit, over temperature, failed switch, open wire, overload, or no load diagnostic.
The IC660BBD020 is compatible with Terminal Assembly IC66*TSD020 version C or later. It is not compatible with any version of IC66*ELD020 or IC66*EBD020 versions A to E Electronics Assemblies. However, these assemblies can get an upgrade to work with IC660BBD020. Any handheld monitor can be used with this block except for IC66*HHM501, which requires some configuration.
Technical Specifications
| Rated Voltage: | 24/48 VDC |
| # of Points: | 16 |
| Input Range: | 18-56 VDC |
| Load Current: | 2 Amp |
| Operating Voltage: | 18-56 VDC |
| Points per Common: | One group of 16 |
The GE Fanuc Genius I-O IC660BBD020 DC Source I/O Block is a solid-state electronic module whose main role is to serve as a connection and control interface between a GE Fanuc Series 90-30 PLC and field devices such as electromechanical sensors and actuators. The GE Fanuc IC660BBD020 DC Source I/O Block is able to provide the power supply voltage needed for the operation of 16 I/O circuits connected to its terminals, and a 24 to 48 Volts DC power source is used for feeding the block itself. Each of the 16 independent I/O circuits that can be controlled and monitored using this I/O block has a corresponding LED indicator light that will show the status of the load being connected to the I/O port assigned to it. The final users can decide if the I/O block should be used as an input block, an output block, or as a combination of both inputs and outputs.
The GE Fanuc IC660BBD020 DC Source I/O Block has several diagnostics features that are available and functional out of the box. The over-temperature diagnostics features will turn off the I/O block any time the temperature goes over 100 degrees Celsius. Short circuit protection is also provided by the GE Fanuc IC660BBD020 DC Source I/O Block for shutting the faulty circuit down in microseconds after detecting a current level above 10 Amps at any port. Other diagnostics features include failed switch detection, open-wire detection, overload, and no-load detection. The wiring coming from or going to the field devices connected to the I/O block is simply screwed into one of the properly identified I/O ports on the block and then it is ready to be used.
Technical Information
Specifications
|
Block Type: CatalogNumbers: 24 / 48VDC16CircuitSourceI / OBlock Terminal Assemblyonly ElectronicsAssemblyonly 24VDC Source 16 Circuit Source I / O Block Terminal Assemblyonly ElectronicsAssemblyonly 24 / 48VDC16CircuitSinkI / OBlock Terminal Assemblyonly ElectronicsAssemblyonly 24VDC 16 Circuit Sink I / OBlock Terminal Assemblyonly ElectronicsAssemblyonly |
16 circuit discrete input and output |
|
IC660BBD020 |
|
|
IC660TSD020 |
|
|
IC660EBD020 (same as block IC660BBD022) |
|
|
IC660BBD022 |
|
|
IC660TBD022 |
|
|
IC660EBD020 (same as block IC660BBS020) |
|
|
IC660BBD021 |
|
|
IC660TSD021 |
|
|
IC660EBD021 (same as block IC660BBD023) |
|
|
IC660BBD023 |
|
|
IC660TBD023 |
|
|
IC660EBD021 (same as block IC660BBD021) |
|
|
Size (height x width x depth): |
8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm) |
|
Weight: |
4 lbs. (1.8 kg) |
|
LEDS (block): |
Unit OK, I / OEnabled |
|
LEDs (each circuit): |
Individual load side indicators |
|
HeatDissipation: |
68.8 Watts with 16 outputs on at 2 amps. |
|
Block to Block Isolation: |
1500 V |
|
Operatingvoltage: |
18–56 VDC (24 / 48 V), 18–30 VDC (24 V) |
|
Ripple (maximum): |
10% |
|
Required DC power: |
150mAtypical / 300mAmaximum |
|
Power supply dropout time: |
10mS |
|
Input Characteristics: For standard input, voltage relative to (DC–) Input ON, 24 VDC supply 48 VDC supply* Input OFF, 24 VDC supply 48 VDC supply* Input processing time (typical) Input impedance (typical) Selectable input filter times Inputdiagnostics |
Source Blocks Sink Blocks |
|
16–24 VDC 0–8 VDC |
|
|
32–48 VDC * 0–16 VDC* |
|
|
0–7 VDC 17–24 VDC |
|
|
0–14 VDC* 34–48 VDC* |
|
|
5.6Kohms (24 / 48V), 1.8Kohms (24V) |
|
|
1.7mS (plus selectable filter delay) |
|
|
5–100mS |
|
|
Open wire, Overtemperature, Failed Switch |
|
|
OutputCharacteristics: Output current (steady state) |
2 amps per circuit |
|
Maximum inrush current |
10 amps up to 10mS |
|
Block output current |
15 amps at 35C |
|
Output OFF leakage current |
1.0 mA |
|
Maximumswitching frequency |
Once per second (high inrush current) |
|
Output turn–on delay (maximum) |
1mS |
|
Output voltage drop |
2.0 volts maximum at 2 amps inrush |
|
Minimum Recommended Load |
50 mA with No Load nabled |
|
Output Diagnostics |
Short Circuit, Overload, No Load, Failed Switch, Overtemperature |
|
Environmental: Operating temperature |
0 to +60C (32 to +140F) |
|
Storage temperature |
–40 to +100C (–40 to +212F) |
|
Humidity |
5 to 95% (non–condensing) |
|
Vibration |
5–10Hz 0.2” (5.08mm) displacement, 10–200Hz at 1G |
Troubleshooting
Troubleshooting IC660BBD020
Troubleshooting information is available on IC660BBD020's website page; it also includes a datasheet, a user manual, and a wiring diagram.
Repair your IC660BBD020
PDF Supply can repair your IC660BBD020 in 3-5 business days. And PDF Supply stands by all of its repairs with a 1 year customer satisfaction warranty.
Customer Questions and Answers
- Question: What is an IC660BBD020? Answer: The IC660BBD020 is a DC 16-Circuit, 24/48 VDC Source I/O Block. This block is an intelligent, configurable block that can interface to a wide range of discrete DC sensors and actuators. The Source Blocks provide current to field output devices.
- Question: Specifically, with what does IC660BBD020 function? Answer: IC660BBD020 functions with 3-wire solid state sensors and electromechanical sensors.
- Question: The configuration of each 16 discrete circuits can be as what? Answer: They can be configured as an input, a tristate input, or an output.
- Question: What is special about the output circuits? Answer: The output circuits can be connected right to input circuits without the need of other components or inversion of logic states.
- Question: Do I need separate block power supply for IC660BBD020? Answer: No, you do not.
- Question: Which features of IC660BBD020 can be configured? Answer:
- Output Pulse Test capability
- Selectable Input Filter Time from 10mS to 100mS
- Output power up defaults
- Output Hold Last State or default
- Question: What are the diagnostic features of this block? Answer:
- Electronic short circuit protection
- Overtemperature protection
- Failed switch detection
- Open wire detection for tristate inputs
- Overload detection and shutdown
- No-load detection
- Question: What is my next step if my IC660BBD020 has failed? Answer: Your IC660BBD020 may need repair.
For more information on the IC660BBD020 Source In/Out Block of the GE Fanuc Genius I/O Series, please see the Datasheet User-Manual.
IC660BBD020 is a Phase B GE Genius block and is compatible with all GENIUS supported PLC systems. The earlier version, IC660CBD020, is a Phase A GE Genius Block, and is only compatible with Series Six and Series Five PLCs.
The final letter in the part number (ex. IC660BBD020K) indicates the revision. Revision K and later use the newer style electronic housing and therefore need the newer style plastic door and may indicate some compatibility issues with the terminal strip.
PDFsupply Tech
The IC660BBD020 is a DC 16-circuit source /sink I/O block with features that includes output pulse test capability. This unit does not require a separate block power supply and advanced diagnostics can locate any causes of installation or run time errors.
Common related search terms: ConfigurationDatasheet, Emerson, Manual, PDF, PLC, Price, Repair, Specification, Troubleshoot, User-Manual, Wiring,
